Models
>
109RB55
109RB55 Hotpoint Range - Overview
Sections of the 109RB55
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Drip Bowl - 6 Inch
PartSelect #: PS244677
Manufacturer #: WB32X10012
This six inch chrome drip bowl is intended for use with tilt lock style surface mount burner element units.
$11.33
In Stock
Broiler Pan - Large
PartSelect #: PS1517612
Manufacturer #: WB48X10056
This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures ...
$30.07
In Stock
Tilt Lock Hinge Mounted Surface Unit - 6"
PartSelect #: PS244050
Manufacturer #: WB30X356
This kit does NOT include the drip bowl. This tilt lock hinge mounted surface element kit includes a 6 inch, three wire, 1350 watt surface element. These standard low rise elements have an attached t...
$79.14
In Stock
Trim Ring - 6"
PartSelect #: PS244460
Manufacturer #: WB31X50
This 6 inch low rise burner trim ring is intended for use with attached style low rise tilt lock surface mount burners on GE electric ranges.
No Longer Available
Questions And Answers for 109RB55
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 109RB55
[Viewing 2 of 2]Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The oven's bottom bake element burned up
First I turned the circuit breaker switch off for the stove unit. I then removed the two screws that hold the element in place at the back of the oven. I then pulled the element out about 3 inches and disconnected the two wires. I attached the new element, bolting the wires into place and then screwed the element back into place on the
... Read more
back wall of the oven. I flipped the breaker switch back on, and turned on the oven. I was done in roughly 15 minutes. The most difficult part was having to shine a flash light into the oven to replace the part, and negotiating the hard cold kitchen floor.
Read less
Parts Used:
-
Dennis from Los Alamos, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
19 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner had shorted out
It was so easy. I turned off the power to the range, loosened the hinge screw and removed the burner unit from the stovetop. Next I removed the two spring clips holding the ceramic housing covering the three connectors. Then I loosened the three screws holding the 3 wire connectors to the burner, reconnected the 3 wires to the new bur
... Read more
ner unit, positioned the ceramic insulator housing and reinstalled the spring clips and finally replaced and tightened the hinge screw. It took about 5 or six minutes, max.
You can do this!
You can do this!
Read less
Parts Used:
-
John from Granite City, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
16 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven element burned completely into.
I first removed the two screws holding the element in place. Then I pulled the element out about 2 or 3 inches and then took out the 2 small screws holding the 2 wires in place. I then removed the old element and discarded it and installed the new one in the reverse order that I took out the old one. It was quite easy to do, only took abo
... Read more
ut 10 to 15 minutes total time.
Read less
Parts Used:
-
John from Kiowa, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!