10997 Lawn Boy Lawn Mower - Overview

The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. Installation is rated as "Easy" by customers and will require a socket set. This part is individually sold, gray, and constructed of metal. R...Read moreefer to your make, model and diagrams to check if this is the right part for you.

This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secures the drive pinion gear to the drive shaft, and if broken due to wear/fatigue/damage, it will need to be replaced.

The Lower Tube is a metal tube used to provide support for controlling the unit. It is part of the handlebar assembly. If there is any visible damage, the part should be replaced. It attaches from the rear frame to the top portion of the handle. Installation is rated as "Easy" by customers and requires pliers, a socket set, and wrench set...Read more. The part comes in black and is sold individually. Refer to your make, model and diagrams to ensure you've chosen the right part.

The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket and is rated as "Easy" by customers. It is mostly used to keep the wheel in place. It fits onto the unit frame and if broken or removed, th...Read moree wheel will fall off. Refer to your make, model and diagram to ensure this is the correct part.

This is a Genuine OEM replacement part used on a variety of Lawn Mowers. This item is made out of Metal and it is Sold Individually. If either the ball bearing or the bearing retainer wear out this will cause the wheels have trouble turning. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the lo...Read moread and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a Genuine Toro replacement part used on a variety of Walk Behind/Push Mowers. This is a Metal Half Moon Key and it is sold individually. The key helps to secure drive wheels to the Transmission Axle.

This is a high quality replacement hardware that is specially manufactured for use on Toro lawn and garden equipment. Two of these screws are generally used to secure the belt guide to the mower deck. Please note this durable metal hex head taptite screw is included per order.

This is a compression spring that is used within various models of lawn mowers and is used to provide stability and extra control to the user during the operation of the equipment. This spring works in tandem with the rest of the axle assembly, such as the key, which is a small metal component that is inserted into slots on rotating parts...Read more like axles, to secure things such as wheels, within the entire assembly. If you notice wobbling, excessive vibrations or difficulty in maneuvering the lawnmower, the compression spring is likely worn, damaged or has lost its tension, and needs replacement. This compression spring is made of metal, is sold as an individual part meaning you will need to consider ordering 2 (one for each side of the lawnmower) and measures approximately 1/3-inch long. To replace this compression spring, you will need a socket wrench, flathead screwdriver and snap-ring pliers. It is recommended you prop your lawnmower up on a piece of scrap wood to make the removal and installation of the new tire easier. Use the flathead screwdriver, if necessary, to remove any wheel covers on your lawnmower, and then use the socket wrench to loosen and remove the wheel. Use some snap-ring pliers to remove the retaining ring on the outside of the wheel axle - you should then be able to remove the pinion connected to the axle. With the pinion out, you can remove the key in its keyway, and underneath should lie the compression spring, which can now be replaced. If you notice any of these parts that are also being removed are worn out or damaged, you will want to replace them immediately to prevent any future performance problems with your lawnmower.

Genuine Toro V-Belt used on Lawn Mowers, it is sold individually. This is the Drive Belt that connects the Transmission and the Blades. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance.

This is a Genuine OEM Toro Pinion Gear, with 15 teeth, which drives the gear on the wheel. This part is sold individually. There are two of these gears used on the Mowers for the left and right sides. If the gear is showing signs of damage or wear it needs to be replaced.

This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal and is sold as an individual part. Screws will need to be replaced when they become stripped.

This is a genuine OEM sourced replacement part designed for use with lawn mowers. This thrust washer helps to secure the pinion gear. It helps to distribute the pressure evenly and provides a tight seal for the connecting pieces. It is made out of metal and it is sold individually. Replacing this washer you would need a wrench and pliers.