Models
>
107RB590G
107RB590G Hotpoint Range - Overview
Sections of the 107RB590G
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Drip Bowl - 6 Inch
PartSelect #: PS244677
Manufacturer #: WB32X10012
This six inch chrome drip bowl is intended for use with tilt lock style surface mount burner element units.
$11.33
In Stock
Drip Bowl - 8 Inch
PartSelect #: PS244680
Manufacturer #: WB32X10013
This eight inch chrome drip bowl is intended for use with with tilt lock style surface mount burner element units.
$17.90
In Stock
Tilt Lock Hinge Mounted Surface Burner Kit - 6"
PartSelect #: PS244042
Manufacturer #: WB30X342
This tilt lock hinge mounted surface element kit includes a 6 inch, three wire, 1350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.
$49.45
In Stock
Tilt Lock Hinge Mounted Surface Burner Kit - 8 Inch
PartSelect #: PS244040
Manufacturer #: WB30X341
This tilt lock hinge mounted surface element kit includes an 8 inch element, three wire, 2450 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come...
$83.46
In Stock
Power Terminal Block Kit
PartSelect #: PS232636
Manufacturer #: WB17X5095
This kit comes with the terminal block, nuts and wires.
$74.64
In Stock
HINGE SUPPORT ASM. - Right Hand
PartSelect #: PS230967
Manufacturer #: WB10X5041
No Longer Available
Questions And Answers for 107RB590G
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 107RB590G
[Viewing 2 of 2]Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The oven's bottom bake element burned up
First I turned the circuit breaker switch off for the stove unit. I then removed the two screws that hold the element in place at the back of the oven. I then pulled the element out about 3 inches and disconnected the two wires. I attached the new element, bolting the wires into place and then screwed the element back into place on the
... Read more
back wall of the oven. I flipped the breaker switch back on, and turned on the oven. I was done in roughly 15 minutes. The most difficult part was having to shine a flash light into the oven to replace the part, and negotiating the hard cold kitchen floor.
Read less
Parts Used:
-
Dennis from Los Alamos, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
19 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven element burned completely into.
I first removed the two screws holding the element in place. Then I pulled the element out about 2 or 3 inches and then took out the 2 small screws holding the 2 wires in place. I then removed the old element and discarded it and installed the new one in the reverse order that I took out the old one. It was quite easy to do, only took abo
... Read more
ut 10 to 15 minutes total time.
Read less
Parts Used:
-
John from Kiowa, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old large 8" stove burner had burnt out, needed replace
Simply took the replacement part ( PS244040, GE WB30X341) and did the quick direct swap using all the new pieces in the burner kit. UNPLUG the stove. Undo the titl arm screw, remove the plastic wire isolation block (2 spring clips), unscrew the 3 wires to the elements, screw the 3 wires to the new element, put in new bakelite wire isolati
... Read more
on block with spring clips to keep the wires seperated, mount and titghten the tilt arm screw. Make sure the burner sits even and flat in the stove top. Plug the stove back in and test.
Read less
Parts Used:
-
Stephen from GOFFSTOWN, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!