The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is mad...Read moree of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it.
Lower rack roller and bracket assembly, grey. Wheel has been updated. If wheel pictured is not like old one, you may need to replace all wheels.
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step gu...Read moreide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely of plastic, and are white in color. The purpose of these parts is to allow your dishrack to roll easily on the support rails. This kit is so...Read moreld individually and contains only one wheel and one axle. Please order the required quantity for your repair. If your dishrack is having trouble rolling in and out you may need replace your rollers and axles.
NOTE: Sold individually. This door spring is four and a half inches long. It is used for some dishwashers. These springs tend to wear out at the same rate, so you should replace both of your dishwasher door springs at the same time.
This is a basket for your dishwasher. It sits in the lower dishrack and holds small utensils during a washing cycle. This basket has six smaller sections where you can separate your cutlery into specific groups. This silverware holder is made entirely of plastic with a crisscross pattern allowing water and small food particles to pass thr...Read moreough it during the cleaning process. This model is grey and roughly 14 inches long, about 6 inches high, and almost 4 inches thick.
This electrically operated propeller causes water to flow through your dishwasher's pump. This impeller is located above the dishwasher's mascerator blade.
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower Rack Roller Missing
379 of 395 peoplefound this instruction helpful.
Sandra from Mount Vernon, WA
Really Easy
Less than 15 mins
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.
Was this helpful?
Thank you for voting!
Water leaking under the dishwasher
78 of 89 peoplefound this instruction helpful.
Dennis from Tryon, NC
Really Easy
Less than 15 mins
Wrench (Adjustable)
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa
... Read moresher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.
Read less
Was this helpful?
Thank you for voting!
plastic attachment for wheel to rack had dried and broken
67 of 133 peoplefound this instruction helpful.
Marla from Columbia, TN
Really Easy
Less than 15 mins
removed the remnants of the old wheels and popped the new ones on....simple
Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!