1069552621 Kenmore Refrigerator - Instructions

I removed two screws on the top and one underneath the unit. Then I disconnected the cable. The hardest part was getting the nut driver on the bottom screw because it was obscured by the unit. The replacement unit plugged right in! I got my first batch of ice in about 20 minutes. All I really needed was the timer unit, but the entire ice maker wasn't much more expensive, especially when you consider the time saved on installation!

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

open ice maker door, use mirror to view slot in front of ice maker, slip piece in place and done

Received my kit quickly. Job was fast and easy. Removed 3 screws with nutdriver and unpluged the wiring harness. Use a flat blade screwdriver to lift the tab on the plastic end cap of the harness. The icemaker comes out in one piece. The wiring harness that came installed on the replacement icemaker matched mine perfectly. (It comes with two others). I plugged the new one in, replaced the screws, bottom one first to help hold it while replacing the top two screws. I used the shut-off arm from my faulty icemaker. Turned the power back on and put 1/2 cup of water in the tray and walked away. Ice dropping into the bin was music to my ears. Didn't need any of the clips or things that came with the icemaker. It was basically a "plug and play". I'm so happy to have ice again, and at a great savings!

I had a technician called out to the house to look at repairing several appliances that all have broken parts after just 3 yrs of use. Hood, Microwave, Oven, Fridge all in need of minor repairs..

Anyway - the estimate was $240 to replace the ice maker. I ordered PS358591 for $104. and it came in a couple days.. I took out one screw - slid out the icemaker, unplugged it - plugged in new one and slid it in the slot - and done !! Took about 20 mins.. didnt need any of the wiring harnesses in the box from partselect. Was way to easy to do !!

Thank you !

First, I unplugged the power to the entire fridge, and then removed the ice tray and ice door. Next, I unplugged the flat plug in the very back left behind the icemaker. Then I removed the 1/4" hex head sheet metal screws (2) and the phillips head screw (1) that hold the icemaker to the left side of the freezer wall. New icemaker came with a different style trip arm, so I used it. Plugged new icemaker in before reattaching it with the same (3) screws. Replaced ice tray and door, plugged in fridge, and waited....Dumped its first batch of ice maybe a couple of hours later. Not much trouble-shooting is needed when the entire icemaker is as easy and relatively inexpensive to replace as this. Twenty minutes, max.

We weren't sure if the problem was in the Water Inlet Valve or in the Icemaker Control & Motor Assembly. The water in the door did work. We removed the Water Inlet Valve & tested it with an Ohm Meter. It tested good so we put it back in. We then ordered the Icemaker Control & Motor Assembly. When it arrived we installed it and waited a few hours but the icemaker still did not fill with water. We telephoned a parts store and were told the problem could be the thermostat or we could replace the whole icemaker. We replaced the whole icemaker.

I have an old DIY home repair book and I saw that the ice maker repair wasn't hard, so I ordered the parts from Part Select. 1 day to arrive...super service. The site is very helpful with diagrams about the parts. The repair was a cinch...EXCEPT I forgot to unplug and got a little zap. The shelf pegs were a breeze because I had read other's stories about how to remove and replace on this site. Go try to do it...get a book at library if you need some direction.

1. Unplug refrigerator to remove power!
2. The timer is inside the control housing located at the top of the refrigerator compartment.
3. Remove two control knobs (the pull off).
4. Remove the front panel escutcheon. The panel is not held in place with screws, but can be gently pried off.
5. Remove two screws from the back that hold the housing in place.
6. Remove screws from the front that hold the housing in place.
7. Drop housing down (still attached by wires - do not detach). Timer is inside housing, located on right.
8. Follow the instructions provided to identify your particular wiring setup. You'll find the wiring diagram (on my model) at the bottom of the refrigerator, alongside the defrost catch pan, behind the airflow grille.
9. Remove connector from timer terminals (4).
10. Remove two screws/nuts that hold the timer in place.
11. Install replacement timer following included directions. Read and follow ALL instructions applicable to your particular model and wiring setup.
12. Reassemble by reversing the steps above.
13. Note: You may need to "jog" the replacement timer when you first plug the refrigerator back in, if the timer happens to be in a "defrost cycle" (the compressor won't start). This can be done by inserting a wide bladed screwdriver into the hole below the timer, aligning it with the timer shaft, and slightly turning the shaft CW. Don't force it, and don't turn it very far.

First I unplugged the frig, and turned offed the water and ice dispenser using the on/off panel switch. I removed the panel by inserting a small flat blade screwdriver at the bottom of the panel where the plastic studs locked the panel in place. By inserting a little upward pressure, the panel popped right ouff. The Micro Switch was very easy to remove and replace. Just make sure that the plunger on the ice dispenser makes solid contact with the switch when depressed.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I have a side by side so in order to access the bi-metal switch I first had to empty out the freezer. The switch is clipped on to the top of the evaporator coil. I had to remove 8 screws to remove the back panel of the freezer compartment. The bi-metal switch was right there in plain view. There are two colored wires that come out of the switch. I tried pulling them out of the socket they were plugged into but gave up for fear of breaking something. I ended up cutting the wires and splicing them together. I used the plastic twist caps. I made sure when I closed everything back up that the open end of the caps were pointing down so no water can accumulate in them. It has been 3 days now and so far so good

Didn't know if part was replaced from the front or back of door. Removed back/inside first. Good excuse to clean mold found in places not normally seen. The only real problem was getting the face off the dispenser without breaking it. I now know it snaps off from the bottom. To replace one little nozzle you have to replace about 10' of tube. When I pulled the old tube out. I attached fishing line to it and used to fishing line to help feed the new tube through the door.

DISCONNECT POWER. Removed all shelves/baskets.Popped upper panel off (just clips in) Removed 6 screws in lower back panel ( 3 each side) slid panel in place but down. You can then easily see the defrost thermostat/defrost termination switch. Cut the wire connectors (pink n brown wire) stripped back wire, attached new defrost thermostat. Thermostat clips on. New thermostat ohm's at 5.5, old one was "open". Slid cover back up meeting the upper cover grooves. Screwed lower panel in. Put shelves etc back in. Plugged in. Turns on, put a bottle of water in freezer. Checked a while later, frozen. has been frozen for a week.
-James

First of all, here's a warning to all -- I took the glass shelf / pan cover out to clean it -- with a sponge wet with COLD water and the shelf literally exploded on me. This is the second such incident. Both times I have been lucky and no one was hurt.

The shelf was easily identifiable by part number based on model number. Easy to locate the model number on plate above top shelf inside refrigerator (right hand side in my case).

Only had to carefully set glass shelf in frame -- no issues. I was able to use a screwdriver to remove the shelf support stud and basically pop the replacement back in with no issue.

Thank you Parts Select for your simplified system to order replacement parts, and the speed with which it was received.