This genuine OEM replacement part is a water filter for your fridge or freestanding ice maker. The filter is used to remove contaminants and particles from the water, to ensure a clean and fresh taste. The filter should be replaced every six to nine months, or after 2000 gallons of water have passed through, whichever occurs first.
If your refrigerators interior light is not working, the door light switch may be the part to replace. It activates the light as the door opens or closes and has two push-on wire connections. Unplug the refrigerator before installation, and confirm fit using your refrigerators model number. This is an OEM part.
Keep ice production in step with available bin space using this ice maker bin thermistor. The probe senses temperature changes as ice accumulates around it and sends that information to the control board, allowing production to pause when the bin is full. A failed sensor may cause overflowing, early shutdowns, or interrupted ice productio...Read moren. Replacing a faulty thermistor helps restore accurate temperature feedback. Disconnect appliance power before installation, handle the probe and wiring gently, and secure the sensor in its original mounting position This is an OEM part sourced directly from the manufacturer.
This ice maker scoop is an OEM refrigerator part designed to retrieve ice from the ice maker bin. It is made of plastic and measures approximately 10 3/4 inches in length and 4 inches in width. The scoop is designed to fit inside the ice bin for easy access. You will need to replace the scoop if it is cracked, broken, or lost. Discard the old scoop and insert the new one into its designated compartment.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door switch module wore out
40 of 55 peoplefound this instruction helpful.
Fred from Oceanport, NJ
Easy
Less than 15 mins
Pliers
Pull out old module... Remove 2 wires... Tape to inside wall [don't want them to fall down into side panel]..
Order new switch..
Fed Ex pkg came on 2nd day..
Install wires on switch... Press into opening... Check door light on..[OK] .. Done
Was this helpful?
Thank you for voting!
Ice bin overfilling
16 of 21 peoplefound this instruction helpful.
Travis from N CHESTERFLD, VA
Very Easy
Less than 15 mins
Nutdriver
I'm an hvac/r technician, and regularly work on ice machines. Begin my pulling the white over beneath the control panel. It snaps in place so pull on the bottom then left out. 1/4 nut driver is all you need, and remove the screw holding the bin thermistor clip to the side. Up to the right , beneath the control panel, behind the plasti
... Read morec panel you previously removed is the mollex connector. Unplug the thermistor and follow instructions in reverse to reinstall.
Read less
Was this helpful?
Thank you for voting!
Needed to replace a broken light switch
13 of 19 peoplefound this instruction helpful.
Ethan from Fort Collins, CO
Really Easy
Less than 15 mins
Screw drivers
Popping out the broken switch was easy once I was able to see how the new switch part was engineered. The switch was made to be replaced, having a simple tension hook on the bottom of the switch which needed to be depressed to pull the switch out of the cabinet. Once pulled out, there were modular plugs for the power line that were easy
... Read moreto pull off the broken switch and plug into the new switch. Pop the new switch back in and VOILA, the lights worked again! Thanks to part select's good diagrams of the actual model of my refrigerator, it was very easy to hone in on the exact part I needed. I did notice one problem with the order as the correct series for the part was displayed earlier in the process, but had the wrong series later in the process. However,. I trusted the system and the part is for the right series and fit well (an exact match, down to the color). Thanks Part Select, I would definitely use you again.