This nickel-safe, unscented ice machine cleaner measures 16 fluid ounces and is used to remove mineral build-up and hard water and is compatible with several makes and models of freestanding ice machines. To use properly, turn off your ice machine and remove the existing ice left in your ice machine. Next, drain the water from your ice ma...Read morechine. Empty the entirety of this cleaner into the empty water pan and activate the cleaning cycle, and once the cycle is complete and you drain the pan again, the cleaning is complete!
For an ice maker to form ice, water circulates over the evaporator plate. This OEM recirculating pump moves that water and is rated at 12 V, 60 Hz, and 13 W. Check your appliances model number to confirm compatibility. Disconnect power and wear work gloves before installation.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Monitor when stored ice reaches capacity with this ice maker bin temperature sensor. Its electrical resistance changes with temperature, providing feedback to the control board. When accumulated ice cools the sensor, the system can pause production until more storage space is available. A faulty sensor may cause overflowing or stop ice pr...Read moreoduction before the bin is full. Replacing a failed thermistor helps restore accurate bin temperature feedback. Disconnect appliance power before installation, secure the wiring connector, and return the sensor to its designated mounting position. This is an OEM part sourced directly from the manufacturer.
The purpose of the light switch in your refrigerator is to automatically turn on the light when the door is opened. If the light does not come on automatically when you open the door, the contacts inside the light switch may be burned out, meaning it is time to replace the switch. This package contains both the new light switch and a smal...Read morel plastic spacer. To complete this repair, you will need to remove the control panel section of your refrigerator. The only tools you will require for this repair are a 1/4-inch nut driver and maybe a small flat blade screwdriver. Be sure to disconnect the power source from the refrigerator before completing this repair.
This is a temperature sensor. It may also be known as an ice maker sensor and is used in conjunction with your ice machine. This piece is roughly 3.5 inches long, almost 2.5 inches wide, and includes the necessary wiring connector. You will find this part located in the water pump area of the ice cube maker. The function of this part is t...Read moreo determine the water level within the water reservoir. Once the water level reaches a certain point, the sensor will signal the controls to fill the reservoir.
This authentic OEM black touch-up paint is specifically designed for repairing minor scratches, chips, or blemishes on your kitchen appliances. The bottle contains 16ml or 0.6oz of black paint and has an applicator brush under the cap, the same way a nail polish bottle is designed. Restoring these visible damages is important because crac...Read moreked or chipped surfaces can become a breeding ground for dirt and bacteria. If your existing bottle of paint has a thick or clumpy consistency, do not use it. Remember to shake the bottle before applying the paint to your appliance. Please keep in mind that this bottle is sold individually.
This ice maker scoop is an OEM refrigerator part designed to retrieve ice from the ice maker bin. It is made of plastic and measures approximately 10 3/4 inches in length and 4 inches in width. The scoop is designed to fit inside the ice bin for easy access. You will need to replace the scoop if it is cracked, broken, or lost. Discard the old scoop and insert the new one into its designated compartment.
This ice maker evaporator thermistor monitors temperature at the evaporator and sends that information to the electronic control board. Its electrical resistance changes as the temperature rises or falls, helping the control manage the freezing and ice release cycles. A damaged sensor or faulty connection may cause interrupted ice product...Read moreion or cycles that run at the wrong time. Replacing a failed thermistor helps restore accurate temperature feedback. Disconnect the appliance from power before accessing the sensor, and handle its wiring carefully during installation. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken light switch
82 of 134 peoplefound this instruction helpful.
Randy from Hays, KS
Really Easy
15 - 30 mins
Socket set
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps
... Read more ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'
Read less
Was this helpful?
Thank you for voting!
was not making ice
48 of 57 peoplefound this instruction helpful.
Richard from North Wilkesboro, NC
Really Easy
15 - 30 mins
Nutdriver, Pliers, Screw drivers
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well
Was this helpful?
Thank you for voting!
Ice maker overfilling with ice and would not stop production when full.
26 of 33 peoplefound this instruction helpful.
Ray from Terry, MS
Very Easy
15 - 30 mins
Nutdriver
Very easy to replace. Down load the Manual online for a completely operating manual. Thermistor can be tested with an Ohm Meter. Proper values are listed in operating manual.