Models
>
1068242050
1068242050 Kenmore Freezer - Overview
Sections of the 1068242050
[Viewing 4 of 4]Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$11.73
In Stock
Door Cam - Black
PartSelect #: PS11752991
Manufacturer #: WPW10329686
The Door Cam is a black plastic part which helps the door pivot shut while keeping the door and hinge in proper alignment. Lubricating this part upon installation may help it move easier. It attaches...
$10.56
In Stock
Door Closing Cam Kit
PartSelect #: PS358690
Manufacturer #: 4318165
This door closing cam kit is intended for use with the bottom of refrigerator and freezer door hinges. The cam helps with the closing of the doors and to keep them slightly in position when opened.
$13.52
In Stock
Condenser Fan Motor Kit
PartSelect #: PS395284
Manufacturer #: 833697
This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant ...
$63.18
In Stock
Screw
PartSelect #: PS11742721
Manufacturer #: WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
$7.91
In Stock
Light Socket Kit
PartSelect #: PS371236
Manufacturer #: 4387478
The light socket in your refrigerator houses the light bulb and connects it to the power source. If your refrigerator light is not coming on when you open the door, you may need to replace the light s...
$70.72
In Stock
Kickplate Support Clip
PartSelect #: PS11746875
Manufacturer #: WP944224
Sold individually.
$11.14
In Stock
Single Hex Head Screw
PartSelect #: PS11742731
Manufacturer #: WP489069
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
$5.42
In Stock
Screw
PartSelect #: PS11742733
Manufacturer #: WP489128
This screw is sold individually.
$13.17
In Stock
Retainer Bar End Cap
PartSelect #: PS11747552
Manufacturer #: WP986540
Sold individually.
$11.10
In Stock
Questions And Answers for 1068242050
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 1068242050
[Viewing 12 of 12]Door won’t open or close
Fixed by
these parts
these parts
Show All
Fridge too warm
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Freezer section too warm
Fixed by
these parts
these parts
Show All
Clicking sound
Fixed by
these parts
these parts
Show All
Light not working
Fixed by
these parts
these parts
Show All
Door Sweating
Fixed by
these parts
these parts
Show All
Fridge runs too long
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Fridge and Freezer are too warm
Fixed by
these parts
these parts
Show All
Too warm
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sometimes the condenser fan would start causing the refrigerator to overheat.
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut ... Read more and strip the wire about two inches from the fan.
Cut and strip the new wire. I cut the new wire in half (about 6 inches.) Connect the two wires, twist and used 2 wire nuts. Tie wrap the wire to the wire harness. Mount the new fan (three screws)
Screw the back panel back on.
Mount the new
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut ... Read more and strip the wire about two inches from the fan.
Cut and strip the new wire. I cut the new wire in half (about 6 inches.) Connect the two wires, twist and used 2 wire nuts. Tie wrap the wire to the wire harness. Mount the new fan (three screws)
Screw the back panel back on.
Mount the new
Read less
Parts Used:
-
Tom from Franklin, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
180 of 204 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door would not close properly. The CAM had broken.
The repair was very simple.
1. Remove the food from the door shelves.
2.Remove the door by first removing the three screws holding the hinge at the top of the refrigerator.
3. Lift door off of the bottom hinge.
4.Replace bottom CAM on bottom hinge (one screw)
5. Replace top CAM and sh ... Read more im on door (one screw)
6. I put a little grease on the cam to make it slide better.
7. Place door on bottom hinge. Remount top hinge.
8. Done and works better than new.
1. Remove the food from the door shelves.
2.Remove the door by first removing the three screws holding the hinge at the top of the refrigerator.
3. Lift door off of the bottom hinge.
4.Replace bottom CAM on bottom hinge (one screw)
5. Replace top CAM and sh ... Read more im on door (one screw)
6. I put a little grease on the cam to make it slide better.
7. Place door on bottom hinge. Remount top hinge.
8. Done and works better than new.
Read less
Parts Used:
-
Thomas from San Clemente, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
143 of 147 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light Would Not Go On In The Refrigerator
First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the le
... Read more
ad wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!
Read less
Parts Used:
-
DANIEL from MINNEAPOLIS, MN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
61 of 77 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!