Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The EDR1RXD1 water filter provides clean, fresh-tasting water by reducing contaminants such as lead, chlorine, and particulates. Designed for easy installation, this filter ensures your refrigerator w...
The lower door closing cam is used in refrigerator doors, it can be located on the fresh food side or the freezer side. It helps hold the door open. This cam is made out of plastic, so it might crack ...
This OEM, clear convertible meat drawer can be used to store meats or vegetables and is designed for the lower portion of your refrigerator, generally. It has its own cold air duct to allow cold air f...
This clear refrigerator door shelf bin is a genuine OEM replacement part designed for select Whirlpool, Kenmore, and Maytag models. Made from high-quality, food-grade PS plastic, it securely holds jar...
This is an OEM glass shelf for a variety of models of refrigerator. This shelf assembly features an approximately 18 inch long and 18-inch-wide white plastic frame and its inner glass pane, and is des...
If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-met...
This is a glass shelf for models of refrigerator. This part acts as a cover, a shelf, and a set of drawer slides all-in-one. This part includes a white plastic frame that doubles as drawer slides for ...
This refrigerator glass shelf serves as a replacement for the crisper pan cover and is designed to sit securely above the crisper drawers, providing both a protective barrier and additional storage sp...
This refrigerator snack pan is the topmost and smallest drawer in the unit, designed to store food items that require refrigeration but not the humidity control of larger drawers. Constructed from cle...
This clear plastic refrigerator crisper drawer is designed to store fruits and vegetables at optimal humidity levels, helping to preserve freshness and extend shelf life. Constructed from durable, tra...
This mounting screw is a genuine OEM replacement part for the door handle in your refrigerator. If you are having trouble shutting the refrigerator door, or opening it, replacing this screw can help s...
$11.77
In Stock
Order now and your part arrives by May 16
Questions And Answers for 10651793412
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Shirlynne
September 24, 2021
I need to replace the led light. The one i ordered is not the correct one.
For model number 10651793412
Hello Shirlynne, Thank you for your inquiry. We have researched the model number you have provided, and the main led light located in the lower portion of the refrigerator section is PS11755866. There is also another one at the top of the fridge which also contains the controls, which is part# PS11755867. Good luck with your repair.
Hello Nancy, thank you for contacting us. To replace the light, first, make sure you are using a light bulb of the same size and shape. The dispenser lights are LEDs that cannot be changed. You can replace the lights in the crisper and freezer sections of your model. To install a light in the crisper section, remove the top crisper drawer for easier access to the crisper light shield. Remove the light shield by squeezing the top and bottom in towards the center and pulling the bottom tabs out of the refrigerator liner, then sliding the top tabs down and out. Replace the light shield by sliding the top tabs up into the slotted holes in the refrigerator liner, then snapping the bottom tabs into place. To install the light in the lower freezer section, remove the light shield by grasping the sides and squeezing it towards the center. Once the side hooks of the shield are free from the freezer lining, pull down the shield. Replace the light shield by squeezing the sides toward the center and inserting side hooks into the slotted holes. Once the side hooks are in place, snap the front tab into the slotted hole. We hope this helps, good luck with this repair!
Did this question help you?
Thank you for voting!
April
March 2, 2023
Need a replacement ice holder mines has a hole in it
For model number 10651793412
Hello April, thank you for reaching out. The ice bucket compatible with your model is part number PS11731153. We hope this is helpful!
Inside light is going dim. How do you replace/change?
Regards.
For model number 10651793412
Hi Don, thank you for reaching out. There are clips on either side of the light module. If you take a small flathead screwdriver and release the tabs, the light module will come down from the ceiling, and then you can unplug the unit and replace it. Please remember to unplug the unit before starting this repair. We hope this helps!
Did this question help you?
Thank you for voting!
Beverly
November 22, 2025
how wide is this frig?
For model number 10651793412
Hello Beverly, thank you for reaching out. Your refrigerator is 32.76 inches wide. We hope this information helps!
Did this question help you?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
WARNING: REPLACING THIS PART REQUIRES CUTTING AND SPLICING ELECTRICAL WIRES. RISK OF ELECTRICAL SHOCK OR FIRE. DO NOT ATTEMPT THIS REPAIR IF YOU ARE NOT EXPERIENCED WITH ELECTRICAL WIRING.
Part Info: The bi-metal strip is clipped onto the evaporator coils and is designed to regulate the defrost coil temperature. If it is n
... Read moreot functioning properly you may notice ice buildup preventing air flow (and preventing proper refrigeration), or more rarely the freezer side may get too warm during the defrost cycle.
1: UNPLUG THE FRIDGE! If there is ice buildup, wait until the ice has melted. A box fan blowing at the ice will help melt it more quickly.
2: Remove the panel covering the evaporator coils. It's located inside the fridge, on the freezer side.
3: Un-clip the bi-metal strip from the evaporator coils.
4: Unplug the wires from the evaporator fan, defrost coil and bi-metal strip, then disconnect the main connector that is plugged into the rear wall.
5: Clip both wires to the old ( bad ) bi-metal strip. Cut close to the casing of the bi-metal strip so there are long wires to splice onto.
6: Strip 1/4 to 1/2 inches of insulation off of the ends of the wires ( depending on the size of the wire-nuts you use). Twist the bare wires slightly to prevent fraying.
7: Do the same for the ends of the wires on the (new) bi-metal strip.
8: Take the ends of the wires belonging to the (new) bi-metal strip and the wires coming from the main plug. Take the like-colored wires, and twist the bare metal ends together.
9: Twist on wire nuts, for both sets of wires. Make sure they are snug, with no bare wire showing.
10: Tape over the wire nuts with electrical tape. Tape over the wires nuts in a spiral fashion, completely covering the nut and both wires that are now spliced together. This will prevent accidental shorting.
11: Plug the main plug back into the rear wall of the fridge. Also re-connect the connectors to the evaporator fan and defrost coil. Make sure the clips on the connectors are snug to ensure a good connection.
12: Clip the new bi-metal strip onto the coils, in the same spot as before. ( Usually just after the small incoming copper tubing that connects to the coils, known as the expansion valve. That is usually the coldest spot on the coils during operation).
13: Replace the panel that covers the coils.
14: Plug the fridge back in... Now you fridge should defrost correctly. If it does not, your defrost coil could be burned out, or the control board could be faulty.
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps
... Read more ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'
