1065172 Kenmore Refrigerator - Overview

The crisper drawer (Crisper Pan, Refrigerator Crisper Drawer) with humidity control is meant to keep your vegetables and fruit as fresh as possible by allowing you to regulate the humidity levels within the drawer. It attaches on the inside of your refrigerator to the bottom of the crisper shelf. This drawer can break from misuse or accid...Read moreental damage. It is also subject to material fatigue over time. If broken or damaged, it may be difficult to slide the drawer in and out, and it should be replaced. This plastic drawer measures 14.92 inches long, 7.6 inches high, and 16.5 inches wide and comes in white/clear.

The EDR1RXD1 water filter provides clean, fresh-tasting water by reducing contaminants such as lead, chlorine, and particulates. Designed for easy installation, this filter ensures your refrigerator water and ice are safe and refreshing with every use

The lower door closing cam is used in refrigerator doors, it can be located on the fresh food side or the freezer side. It helps hold the door open. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace the door closing cam. To successfully install ...Read morethis part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. Lubricating this part may help with installation. This replacement part is sold individually. This part will fit both the left and right side of your refrigerator door. To make the repair, remove the top hinge cover, then the top hinge support. Lift the door from the bottom support and remove the old door cams. Replace the cams, using a little lubricant if necessary, and place the door back on the lower hinge support. Replace the top hinge support and your repair is complete!

This OEM, clear convertible meat drawer can be used to store meats or vegetables and is designed for the lower portion of your refrigerator, generally. It has its own cold air duct to allow cold air from the freezer to flow into the drawer. You could have a broken or faulty drawer if you find that the food is kept within is spoiling or dr...Read moreying out quickly. The drawer should slide open and closed with ease. If your drawer will not easily slide open or closed, check the tracks that the drawer slides on. If the tracks are not damaged, the drawer itself could be at fault and should be replaced. Inspect it for visible damage like cracking or warping, which should be obvious. This part measures approximately 16 7/16 inches wide x 14 5/16 inches deep x 7 5/8 inches high and is a genuine OEM replacement part. It is sold individually. Note that there are several different types and options for the lower vegetable and meat drawers for your refrigerator, and you should check your user manual carefully to ensure that this is the drawer you are looking for.

This clear refrigerator door shelf bin is a genuine OEM replacement part designed for select Whirlpool, Kenmore, and Maytag models. Made from high-quality, food-grade PS plastic, it securely holds jars, bottles, and other items on the right-hand side of the upper refrigerator door. The bin features reinforced edges for added durability an...Read mored wear resistance, and some versions include a built-in soda can organizer for enhanced storage. Installation is tool-free, with the bin snapping directly into the designated slot. Compatibility should be verified using your refrigerator’s model number prior to installation.

This is an OEM glass shelf for a variety of models of refrigerator. This shelf assembly features an approximately 18 inch long and 18-inch-wide white plastic frame and its inner glass pane, and is designed to hold whatever food items you need it to. If your current shelf is cracked, shattered, or simply no longer able to support itself, i...Read moret should be replaced immediately. To replace this shelf, simply align the shelf with the inner grooves of the refrigerator and pull the old one out, and then slide in the new one.

If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator doe...Read mores not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.

This white ice bin auger drum comes with a washer.

This is a glass shelf for models of refrigerator. This part acts as a cover, a shelf, and a set of drawer slides all-in-one. This part includes a white plastic frame that doubles as drawer slides for the snack pan underneath and measures approximately 17.5-inches wide by 18.5-inches long, along with a glass insert that allows for items to...Read more be set on it. If your current glass shelf is shattered, cracked, or simply missing, it should be replaced. Replacing this shelf is easy, as you only need to carefully pull it out, then slide in the new shelf. This shelf is supplied by the original equipment manufacturer and does not come sold with any other parts than those mentioned.

This refrigerator ice bucket is a genuine replacement component designed to store ice produced by the icemaker before dispensing. Compatible with a wide range of models from Whirlpool, KitchenAid, Kenmore, Maytag, and Amana, it is constructed from durable plastic to withstand regular use. The container is sold as a standalone part and doe...Read mores not include the auger or other internal components. Replacing a cracked or missing ice bucket helps restore proper ice storage and dispensing functionality. Installation is straightforward and typically requires no tools—simply follow the instructions in your owner's manual to ensure proper fit and alignment.

This part is also known as a shelf frame. This drawer cover is for refrigerators. Drawer cover has rail brackets under the cover that hold the drawer and allow the drawer to slide in and out on the rails. Follow the instructions in the owner's manual or installation guide when installing this part. This comes with glass.

This refrigerator glass shelf serves as a replacement for the crisper pan cover and is designed to sit securely above the crisper drawers, providing both a protective barrier and additional storage space. Crafted from tempered glass, it offers a durable and safe surface that helps contain spills and maintain organization within the refrig...Read moreerator. The transparent design allows for easy visibility of items stored below. Measuring approximately 16.5 inches in width and 13 inches in depth, it fits directly into the existing white plastic frame without the need for tools or disassembly. Ideal for replacing cracked or broken glass, this shelf restores both function and appearance to your refrigerator interior. Sold individually.