My Orders
1060M Simplicity Snow Blower - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$6.40
In Stock
Snow Blower Shear Pin
Part #703063
Shear Pins are designed to break off in order to prevent further damage to your machine. Because they are designed to break, we recommend having a few spares on hand. This part is made of metal, is silver, is not part of a kit or assembly, and is sold individually.
A Shear Pin will break when you hit a large chunk or ice or other debris...Read more. Once it is broken, it will need to be replaced. You will need pliers to complete this repair.
Customers rate this repair as Easy.
Read less
$25.54
In Stock
Pulley/spring Assembly
Part #498144
This manufacturer approved recoil starter pulley is designed for lawn and garden equipment engines. The recoil starter engages the drive cup on the flywheel to start the engine when pulled. This assembly includes: Plastic Pulley and a Metal Recoil Spring.
$21.68
In Stock
Gear Universal
Part #1718593SM
The OEM Universal Gear attaches on the chute control rod, and meshes with the worm gear in order to adust the chute. Using the part is rated as "Medium" difficulty by customers, and requires pliers, a socket set, wrench set, drift punch and hammer. If the part breaks there may be broken or chipped teeth which will prevent it from adjustin...Read moreg the chute, and should be replaced. This part is constructed of metal and comes in gold. Refer to your make, model and diagrams to ensure this part is right for your machine.
Read less
$8.09
In Stock
Engine Oil Seal
Part #391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.
Read less
$10.65
In Stock
Bearing, Ball 11/16x1
Part #1705897SM
This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.
Read less
$6.40
In Stock
Key-flywheel
Part #222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.
$6.40
In Stock
Lawn Mower Cotter Pin
Part #703312
This cotter pin is an OEM part that is 1.25 inches long, gold in color, and sold individually. Made of metal, it can have a range of applications on a variety of lawn and garden equipment. Generally, you will need to replace this part if it becomes broken due to age and wear, or if you need to remove it for making other repairs.
This is...Read more an easy repair that only requires a pair of pliers to carry out. You need to bend one end around the shaft or bolt and bend the other around the back end of the bolt to complete the repair.
Read less
$56.10
In Stock
Armature-magneto
Part #591459
It is an authentic amature-magneto (ignition coil) which was specially designed for use with Briggs and Stratton engines used on lawn and garden equipment. The purpose of this item is to deliver electric current for the ignition system. It produces pulses of high voltage which then are sent to the spark plugs. It is mainly made out of met...Read moreal and it is sold individually. Please note a spark plug boot is sold separately. Please note replacing this module would differ based on your unit, however the basic steps would be the same. To complete this repair you would need screwdriver set. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Install the red wire • Set the gap • Install the black wire • Reassembly and test the unit
Read less
$14.76
In Stock
Snow Blower Greased Bearing
Part #2108202SM
This Ball Bearing is an individually sold, silver/black, metal part. It reduces friction in the spindle assembly between the spindle shaft and the spindle housing. If broken due to wear/fatigue, you will hear a grinding, growling, rumbling or screeching sound, and should replace the part. Refer to your make, model and diagrams to ensure this is the right part for you.
$10.90
In Stock
Rod-push
Part #592673
This replacement push rod is specially designed for use on Briggs and Stratton engines. It is an authentic part supplied directly from original equipment manufacturer. The push rod is connected to the camshaft to push the exhaust valve open during the exhaust stroke. A bent rod can not only affect your engine's performance, it can serious...Read morely damage other parts if the problem is not taken care of immediately. Please note, this assembly includes the (1) push rod and (1) tappet valve.
Read less
$8.87
In Stock
Snow Blower Bushing
Part #1667588SM
Sourced directly from the original manufacturer, this Bushing is used to reduce friction on your snowblower. It is made of durable white plastic, is not part of a kit or assembly, and is sold individually.
This part should be replaced if it is worn or damaged, and you may experience problems operating the chute if it is malfunctioning. ...Read moreYou will need a wrench, a socket set, and pliers to complete this repair.
Customers rate this repair as Medium difficulty.
Read less
$8.21
In Stock
Plug-spark Ems
Part #691043
This spark plug is an authentic OEM replacement part, it is not an aftermarket equivalent. It is specially made for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. A spark plug helps to deliver electric current from an ignition system to the combustion chamber. Please note, this item is sold indi...Read morevidually. You should always gap the spark plug in accordance with the owners manual of the outdoor product you have. Replacing a spark plug you will need a apark plug wrench or a socket wrench to get the job done.
Read less
Common Symptoms of the 1060M
How this model fails, and the parts that fix it.
Will Not Start
Fixed by
these parts
these parts
Show All
Cannot pull starter cord out or engine will not turn over
Fixed by
these parts
these parts
Show All
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More