1043-2 Briggs and Stratton Pressure Washer - Overview

This item is an authentic OEM sourced O-ring kit that replaces worn or damaged O-rings for the gun, hose and wand.Unfortunately, over time o-rings will wear out and they may begin to crack eventually requiring replacements. Refer to the appropriate diagrams for your model to ensure the correct replacement procedure. A screwdriver and a wr...Read moreench set might be needed to take apart and reassemble the equipment. Note, this kit is sold as an individual item.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

This is a genuine replacement part that has been sourced from the original manufacturer to be used with generators and pressure washers from Briggs & Stratton and Snapper. The vibration mount fits between the engine and the frame assembly and is used to reduce vibration between the motor and frame. This item is sold as an individual replacement part.

This handle fastening kit includes two plastic thread wingnuts and two carriage bolts, which are essential for securely attaching the handle assembly to your pressure washer. The handle assembly is typically located where the handle connects to the main body of your machine. When these parts are broken, the handle will feel wobbly or loos...Read moree, and there may be visible damage to the mechanism. It is crucial to fix the assembly promptly, as a loose handle can pose safety risks and make it difficult to operate the pressure washer effectively. Please note that this genuine OEM kit is sold individually, and the handle itself is not included.

This is an authentic OEM sourced part that is intended to be used with small engines from Briggs & Stratton and Toro. The shut-off valve attaches to the bottom of the fuel tank and is used to link the fuel line and to control the flow of fuel that goes to the engine. This item is available as an individual replacement part.

This is a genuine Briggs & Stratton replacement part. The oil seal is designed by the manufacturer for use in pressure washers. This part is placed in the crankcase to prevent inadvertent oil leakage. You may require a screwdriver or Allen wrench when replacing this item. This part is sold individually.

This replacement trigger gun assembly is specially designed for use with a variety of pressure washers. It is the essential part of the unit that allows user to direct and control the spray. Please note the wand and the hose are both sold separately. This pistol assembly is made out of plastic with metal fittings. This handle is only for pressure washers up to 3000-psi using M22 hose connector.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton generators and pressure washers. The purpose of this component is to reduce the vibration of a working unit, unfortunately, over time it may begin to fail eventually requiring a replacement. Please make sure to refer to...Read more the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality vibe mount with a washer is sold individually.

It is an authentic item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton and Troy-Bilt equipment. This is an identical replacement for a missing or a faulty push nut that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct locat...Read moreion and application of this component. Keep in mind this high-quality push nut is made of durable plastic with metal and is sold in a pack of two.

This authentic item is supplied directly from the original equipment manufacturer for use with generators and pressure washers made by Briggs & Stratton. The seal goes between the pilot spacer and the spacer plate. A set of pliers and a wrench may be necessary during the installation of this part. It may become broken and will need to be ...Read morereplaced. This item is made of hard rubber and is available as an individual replacement part.

The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or damaged, the nut and part may be loose and it should be replaced. Check your make, model and diagram to ensure you are choosing the correct part.