Models
>
1036417612
1036417612 Kenmore Range - Overview
Sections of the 1036417612
[Viewing 6 of 6]Keep searches simple, eg. "belt" or "pump".
Drip Bowl - 6 Inch
PartSelect #: PS244697
Manufacturer #: WB32X107
The drip bowl on your range is designed to catch any spills that may occur when cooking. This drip bowl is chrome in color and is 6 inches in diameter. The chrome drip bowl is intended for use with ro...
$11.92
In Stock
Drip Bowl - 8 Inch
PartSelect #: PS244696
Manufacturer #: WB32X106
Drip bowls are located under the heating elements and catch grease and spills that come from cooking on your stove top. If your drip bowl is damaged or rusted, it could allow grease to drip inside you...
$22.07
In Stock
Single Heating Element Support Clip
PartSelect #: PS243701
Manufacturer #: WB2X9719
The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this r...
$16.68
In Stock
INFINITE HEAT SWITCH KIT
PartSelect #: PS16216966
Manufacturer #: WB21X36771
The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.
$51.36
In Stock
Rear Drawer Glide
PartSelect #: PS243417
Manufacturer #: WB2X9146
Also called Rear Block.
No Longer Available
Drawer Glide Block
PartSelect #: PS243419
Manufacturer #: WB2X9148
This part attaches to the drawer support to help guide the bottom drawer.
No Longer Available
Questions And Answers for 1036417612
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 1036417612
[Viewing 2 of 2]Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Large burner would operate on high setting only.
1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
Parts Used:
-
Ernest from Bellevue, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
20 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Could not find the correct replacements (burners & drip pans)
After months of buying the wrong parts & cost I discovered this site So easy to order & quick delivery, plus very easy installation. Thank you. I also wanted to add that the reps (Tanisha & Matthew) were extremely helpful & informative. I can only hope all the reps equal their performance. I will definitely be using this site, before an
... Read more
y other source. Knowledge & cost is also important to me & that need was met. Good job!
Read less
Parts Used:
-
Barbara from JEFFERSON, GA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
13 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element dangling
-
Victor from Miami Beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!