Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
100902-4000-82 Briggs and Stratton Engine - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air...
This is a carburetor diaphragm, which is an OEM part that pumps fuel from the tank to the engine. It is roughly 1x2 inches and black in color. Sold individually, this part can fail due to fatigue and ...
This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually...
Genuine Manufacturer Approved replacement part used on a variety of Engines. This is a tube pick-up for 3-5HP horizontal and 5HP vertical engines with 2 and 3 quart tanks and a pulsa jet carburetor. T...
Discover the power of optimal engine performance with the Briggs and Stratton Starter Clutch. A vital piece of your garden equipments engine, this starter clutch engages your machines flywheel while k...
The cylinder head gasket, also known just as the head gasket, is an OEM part sold individually. Grey in color, the head gasket provides a seal between the cylinder head and the engine block in your en...
This magneto, also known as an ignition coil, is a genuine OEM replacement part for outdoor power equipment. It generates the spark needed to ignite the air-fuel mixture in the engine’s combustion cha...
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should ...
This item is available as an individual replacement part but also includes the screws. The muffler deflector attaches to the lo-tone muffler and is made of metal. A nutdriver might be required during ...
The Breather Gasket is OEM and used to provide an airtight seal for the breather assembly. It is a gray part, attached between the breather cap and engine. Installation is rated "Easy" and will requir...
Removed old sparkless magneto, replaced with new part PS9278124 Magneto, and still no spark. The only conclusion that I can draw, is this magneto is defective,
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the m
... Read moreuffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
