09898-1 Briggs and Stratton Pressure Washer - Overview
Sections of the 09898-1
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$27.33
In Stock
Grommet,tank
PartSelect #: PS9307985
Manufacturer #: 83465GS
This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The m...
$6.40
In Stock
Oil Seal
PartSelect #: PS9175910
Manufacturer #: 93680GS
This is a genuine Briggs & Stratton replacement part. The oil seal is designed by the manufacturer for use in pressure washers. This part is placed in the crankcase to prevent inadvertent oil leakag...
$11.29
In Stock
Seal Lo-pres "u" Pak
PartSelect #: PS9163362
Manufacturer #: 93667GS
This authentic item is supplied directly from the original equipment manufacturer for use with generators and pressure washers made by Briggs & Stratton. The seal goes between the pilot spacer and the...
$15.03
In Stock
Screw
PartSelect #: PS9294546
Manufacturer #: 690904
It is a genuine item that is supplied by the original equipment manufacturer for use with lawn and garden equipment. This is an identical replacement for a faulty or a missing hardware that was instal...
$17.57
In Stock
Pin - Hanger
PartSelect #: PS9170440
Manufacturer #: 95194MA
This authentic OEM sourced part is made for use with Murray riding lawn mowers and garden tractors. It is one of the special hanger pins which are utilized to secure suspension brackets to the main de...
$28.21
In Stock
Cap-fuel Tank
PartSelect #: PS11830156
Manufacturer #: 846987
This is a genuine OEM sourced component that is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is designed to keep the fuel in the tank...
$33.99
In Stock
Common Symptoms of the 09898-1
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!