09716 - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This is a genuine OEM sourced hardware that is specifically made for use with Toro lawn and garden equipment. It is a standard hardware which may have multiple applications depending on the model of your unit. Please make sure to refer to the appropriate diagrams for the correct location and application of this part. Keep in mind this hig...Read moreh-quality flange nut is made of durable metal and is sold individually. Note, you will need a wrench to secure or remove it.

This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it becomes lost or broken and may require a wrench during installation. This is an OEM Toro part sourced directly from the manufacturer and used in snowthrowers.

The Nut-Flange, Ni, simply known as a Flange Nut, is a silver metal individually sold part which can be applied with a wrench or socket and torque wrench. Simply torque the part to the manufacturer specifications. It is used to secure the idler arm assembly to the frame, and will need to be replaced if damaged. You can tell if it is brok...Read moreen if there are signs of visible damage, or the part won't tighten all the way due to damaged threads. Customers rated this repair as easy.

This rubber oil seal is supplied directly from the original equipment manufacturer for use commonly with snowblowers and a variety of other outdoor power equipment. It can be used to retain gear oil, seal the transmission, and prevent it from leaking out of the engine. The seal keeps the rotating parts adequately lubricated and protects t...Read morehem from friction damage. The seal also prevents dirt and debris from entering and damaging the equipment components. Over time the rubber material may wear down or tear, leading to oil leakage, increased friction, overheating, and damage to the equipment. To replace the seal, first drain the oil and use a seal puller or flat screwdriver to remove the old seal. Clean the area thoroughly to ensure a good fit for the new seal and add a thin layer of oil around the seal. Align the new seal on the mounting surface and use a seal driver or socket to press the seal down until it is secure. Remember to refill your oil before starting your equipment again.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

This authentic manufacturer-sourced screw is made for use with Toro lawn and garden equipment. It is an identical replacement for a missing or a damaged hardware that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the exact location and the correct application of this hex screw. It is made of durab...Read morele metal and is sold as an individual item. A wrench will be needed to secure or remove it.

This item is priced individually. The flat washer goes next to the hub cap and is made of metal. During the installation process, a wrench might be needed to replace this part. It will need to be replaced if it bends or breaks. This is a genuine Toro part sourced directly from the manufacturer for use in lawn mowers and lawn tractors.