09698 Briggs and Stratton Engine - Overview

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

This OEM grommet, also called a 90-degree breather tube, is sold individually. Black in color and made of rubber, this is a 90-degree elbow for the crankcase breather tube of your mower engine. If you notice a reduction in the mower engine performance, and engine backfires, this part is likely to be in need of replacing. It can develop cr...Read moreacks due to fatigue, and our troubleshooting tip is to inspect this part if dark smoke is coming out of the exhaust, it is a telltale sign. This is an easy repair to make, and does not require any tools. The new grommet attaches on the breather tube fromt he crankcase to the carburetor.

Genuine Briggs and Stratton replacement part, it includes the Diaphragm and Diaphragm Gasket. The purpose of the Diaphragm is to draw out fuel into the engine. The diaphragm is forced inward by ambient air pressure. The diaphragm is connected to the needle valve and as it moves inward it opens the needle valve to admit more fuel, this r...Read moreeplenishes the fuel as it is consumed. As fuel is replenished the diaphragm moves out due to fuel pressure and a small spring, closing the needle valve. Most manufactures will have rebuild kits that contain new Diaphragms in them.

This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually. Over time, you may notice that you are having trouble retracting your pull cord, which could be a symptom of the rewind starter spring f...Read moreailing due to fatigue or wear. Replacing this part is a repair our customers found easy. Locate and replace the start spring inside the starter housing; no special tools are required for this job.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

Genuine OEM replacement primer bulb for engines with a pulsa prime carburetor. This part is sold individually. It includes the Rubber Bulb and the Plastic Collar to attach it. A primer sends gas into the carburetor so it can create a fuel and air mixture that is ready to go right into the cylinder and keep the engine running. Over time a ...Read moreprimer bulb can dry out and crack. If the bulb is damaged it will not create suction and will not function as needed, therefore it will need to be replaced.

Hard starting may come from the recoil system instead of the carburetor or spark plug. If the rope pulls but the engine does not turn, the starter clutch may be worn, dirty, or jammed. The clutch turns the crankshaft during starting and lets go when the engine runs. First inspect the rope, rewind spring, pulley, flywheel screen, and clutc...Read moreh bearing. Confirm fit with the complete engine number. Remove the spark plug wire, wait for hot parts to cool, and keep dirt out of the bearing area. Test free movement before putting the shroud back on.

This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.

The O-Ring is a black rubber part, used to provide a seal between two pieces. It can be used in various locations on a variety of equipment. Installation is rate as "Easy" and will require a screw driver, pliers, socket set, and wrench set. If broken, damaged, or worn due to fatigue, you will have a leak and the part must be replaced. Refer to your make, model and diagrams to see if this is the right part for you.

This spark plug boot is a genuine OEM Briggs & Stratton replacement designed to fit securely over the spark plug, protecting the connection from moisture, dirt, and debris. Its durable, elbow-style design helps ensure reliable ignition and easy installation, making it an ideal replacement when a cracked, loose, or worn boot causes hard starting, misfires, or inconsistent engine performance.

This OEM engine screw is a genuine Briggs & Stratton replacement fastener designed for secure, vibration-resistant attachment of engine components in small gasoline engines and outdoor power equipment. Manufactured to exact factory specifications, it provides proper thread engagement and clamping force to help prevent loosening, reduce vi...Read morebration, and maintain long-term engine reliability under operating stress. Built with durable, corrosion-resistant materials for extended service life, it is an ideal replacement when original screws are missing, stripped, or worn, helping ensure safe assembly, consistent performance, and proper engine operation.

This is a genuine OEM sourced part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardwa...Read morere. Keep in mind this high-quality item is made of durable metal and is sold individually.