09085-4 Briggs and Stratton Generator - Overview

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

Difficulty pulling the starter rope or a cord that stays extended can result from a damaged recoil pulley. This wheel guides and stores the rope while helping turn the engine during starting. Similar symptoms can come from a frayed rope, seized engine, bent starter housing, broken pawls, or weak return spring, so check those items first. ...Read moreMatch the replacement to the full engine model, type, code, and equipment model. Work on a cool engine with the spark plug lead removed. Release spring tension slowly and keep your face and hands clear of the starter housing. Route the rope correctly, confirm smooth return, and reinstall every guard before starting the engine.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

Hard starting may come from the recoil system instead of the carburetor or spark plug. If the rope pulls but the engine does not turn, the starter clutch may be worn, dirty, or jammed. The clutch turns the crankshaft during starting and lets go when the engine runs. First inspect the rope, rewind spring, pulley, flywheel screen, and clutc...Read moreh bearing. Confirm fit with the complete engine number. Remove the spark plug wire, wait for hot parts to cool, and keep dirt out of the bearing area. Test free movement before putting the shroud back on.

An engine that surges, stalls, or will not stay running can have dirt or worn seals inside its float carburetor. This rebuild kit contains gaskets and small service pieces for restoring the carburetor rather than replacing the complete unit. Inspect the fuel supply and ignition system first, then confirm the engine identification and carb...Read moreuretor design. Work only on a cool engine in a ventilated area. Drain all fuel, disconnect the spark plug wire, and keep sparks and cigarettes away. Photograph the linkages, clean passages without enlarging them, install each gasket in the correct order, and check carefully for leaks before starting the engine.

This is a genuine OEM sourced replacement air cleaner cartridge commonly utilized on Briggs and Stratton engines. It installed to filter our dust and other contaminants from entering carburetor and the engine. Please note, this pleated paper filter is sold individually. Keep in mind that the foam pre-cleaner is sold separately. Replacing...Read more this air cleaner cartridge is a simple task that should only require a wrench. • Remove the cover • Remove the old cartridge • Secure the new one in place • Secure the cover

This driven ring is an OEM part direct from Snapper. The flexible plastic ring is compatible with many lawn mowers. This item is often fitted between the driven disc assembly and ring retaining plate, assisting the drive disc with propelling the mower. A screwdriver, wrench set, pliers are needed for the repair. This item is sold individually.

This spark plug boot is a genuine OEM Briggs & Stratton replacement designed to fit securely over the spark plug, protecting the connection from moisture, dirt, and debris. Its durable, elbow-style design helps ensure reliable ignition and easy installation, making it an ideal replacement when a cracked, loose, or worn boot causes hard starting, misfires, or inconsistent engine performance.

This is a high-quality manufacturer-sourced part which is made for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It helps to distribute the pressure evenly and provide a tight seal for the breather. Over time it may become brittle and begin to crack eventually requiring a replacement. For the proper...Read more application please refer to the appropriate diagrams of your model. This high-quality part is made of durable composite material and is sold individually. You will need a screwdriver and a wrench set to remove and reattach the breather.

This cylinder head gasket is used on small engines to seal the cylinder head to the engine block, maintaining proper compression and preventing leaks of combustion gases and oil. Made from heat-resistant material, it supports reliable engine operation and performance. It’s a direct replacement for worn or damaged gaskets during engine repair or maintenance to restore proper sealing and smooth running.