0707 - Overview

This is a replacement screw, also known as a shear pin that is used in several pieces of outdoor power equipment. It is made of metal and is approximately 2 inches in length. It is a hex head screw and is sold individually. This is an OEM part sourced directly from the manufacturer.

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This is an authentic item that is supplied by the original equipment manufacturer for use with Toro lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this i...Read moretem. Keep in mind this high-quality nut is made of durable metal and is sold individually.

This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it becomes lost or broken and may require a wrench during installation. This is an OEM Toro part sourced directly from the manufacturer and used in snowthrowers.

The flat washer is an OEM replacement part that provides a wide surface area to distribute the load of a bolt or a screw when it is installed. This protects the part being fastened from getting damaged or deformed and provides a more secure fit for the bolt/screw. This flat washer is made of steel and has a diameter of 0.375 inches and a ...Read morethickness of approximately 0.063 inches. To replace the flat washer, first unthread the bolt/screw before using a flathead screwdriver to carefully pry it off. Clean the area, place the new flat washer in position, and thread the bolt/screw back on. Sold individually.

The lock washer goes next to the flat washer and is made of metal. It is available as an individual replacement part. This genuine item is supplied by the original equipment manufacturer for use with snowblowers made by Toro and Lawn Boy. A wrench might be helpful during the installation of this part. This item may become broken and will need to be replaced.

It is a genuine OEM sourced replacement part which is specially designed for use with Toro snowblowers. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality screw is made of durable metal and is sold individually.

It is made of metal and is sold individually. The screw connects to the idler pulley. A socket set might be needed during the installation process. Over time this part may become stripped and will need to be replaced. This part is an OEM from Toro and Lawn Boy for use in snowthrowers, tillers, blower-vacuums, and lawn tractors.

This replacement hardware is sourced from original equipment manufacturer for use with Toro snowthrowers. It is standard hardware which has multiple applications, please refer to appropriate diagrams for correct location and use of this locknut. This part is made from durable metal and it is sold individually.