040786-00 Briggs and Stratton Generator - Overview

This replacement oil filter is a genuine OEM sourced item commonly utilized on Briggs and Stratton engines that are commonly installed on lawn and garden equipment. This filter helps to remove harmful contaminants from engine oil that is needed for operation. This part is manufactured in accordance with applicable EPA emissions regulation...Read mores to maintain optimum engine performance. It is recommended to replace it at least once a season. Please note this oil filter is sold individually requiring a wrench to secure or remove it.

This is a genuine replacement part manufactured for use with small engines. The spark plug is used to fire the air-fuel mixture inside the cylinder. This spark plug is available as an individual replacement part, please see model diagram for associative parts.

This is available as an individual replacement part and is made of flexible material. The Exhaust Gasket attaches to Muffler and helps to create a seal. If this part becomes broken it will need to be replaced and may require a wrench during the installation. It is an OEM Briggs & Stratton part directly sourced from the manufacturer for us in Generators and Engines.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This is a genuine replacement part that has been sourced from the original manufacturer to be used with lawnmowers from Murray, Snapper, and Simplicity. The metal bolt is used with several different models of mowers and the application of the bolt can vary based on the individual equipment. It is recommended to review your model's illustr...Read moreated part list to determine the screw's usage and compatibility. This item is sold as an individual replacement part.

It is an authentic OEM sourced item which is specially produced for use with snowthrowers, generators, and rear engine riders made by Murray, Briggs & Stratton, Snapper, and Simplicity. The nut is made of metal and attaches to the starter switch. During replacement, it may require a wrench to help install this part correctly. It may becom...Read moree broken or stripped and will need to be replaced. This part is available as an individual replacement.

It is a genuine OEM sourced component which is specially designed for use with lawn and garden equipment. It is an identical replacement for a missing or a faulty washer that is utilized to provide a tight seal between connected parts. Please make sure to refer to the appropriate diagrams of your model for the correct location and applica...Read moretion of this hardware. Keep in mind this high-quality washer is made of durable metal and is sold individually.

Screw hex 1/4-20x.5

This is a genuine replacement part that has been sourced from the original manufacturer to be used with small engines. The metal hex head screw is used to secure the muffler assembly to the cylinder. This screw is sold individually but four screws may be required, a hex socket wrench is needed to install this item.