04054 - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This is an authentic Briggs & Stratton replacement part sourced from the original manufacturer for use with small engines. The special screw includes a washer and is commonly used to secure the engine's exhaust manifold. The screw is available as an individual replacement part.

This is an authentic manufacturer sourced replacement part designed for use with Toro walk-behind lawn mowers. This part helps to secure the mower wheel, allowing it to rotate freely. It is made out of metal and it is sold individually. To replace this part you would need a wrench and pliers.

This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.

This metal ball bearing reduces friction and evenly distributes weight among the rotating parts in your lawn equipment. These bearings can be found in various areas such as the wheels, in pulleys, blades or augers. When the bearing is damaged, you may notice a few things. Your machine may produce rough or grinding noises and excessively p...Read morelay or wobble. The affected part may also become stuck. Immediate replacement is necessary to prevent increased friction, inefficient performance, and potential equipment failure. Removing the bearing depends on your model, so consult your user manual for guidance. You will need to use a screwdriver or pliers to remove the surrounding components around the bearing and a bearing puller, pry bar, or mallet to release the bearing itself from its housing. As ball bearings wear out together, it is advisable to replace all of them at once. Ensure you verify the number of bearings your machine needs before purchasing this OEM replacement part as it is sold individually.

This is available as an individual replacement part and is made of flexible material. The Exhaust Gasket attaches to Muffler and helps to create a seal. If this part becomes broken it will need to be replaced and may require a wrench during the installation. It is an OEM Briggs & Stratton part directly sourced from the manufacturer for us in Generators and Engines.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.