04043 - Overview

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers from Toro and Lawn Boy. The shoulder screw is commonly used to secure the side fenders to the mower's frame assembly. This bolt is sold as an individual replacement part.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

This is an authentic Briggs & Stratton replacement part sourced from the original manufacturer for use with small engines. The special screw includes a washer and is commonly used to secure the engine's exhaust manifold. The screw is available as an individual replacement part.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This metal ball bearing reduces friction and evenly distributes weight among the rotating parts in your lawn equipment. These bearings can be found in various areas such as the wheels, in pulleys, blades or augers. When the bearing is damaged, you may notice a few things. Your machine may produce rough or grinding noises and excessively p...Read morelay or wobble. The affected part may also become stuck. Immediate replacement is necessary to prevent increased friction, inefficient performance, and potential equipment failure. Removing the bearing depends on your model, so consult your user manual for guidance. You will need to use a screwdriver or pliers to remove the surrounding components around the bearing and a bearing puller, pry bar, or mallet to release the bearing itself from its housing. As ball bearings wear out together, it is advisable to replace all of them at once. Ensure you verify the number of bearings your machine needs before purchasing this OEM replacement part as it is sold individually.

This is available as an individual replacement part and is made of flexible material. The Exhaust Gasket attaches to Muffler and helps to create a seal. If this part becomes broken it will need to be replaced and may require a wrench during the installation. It is an OEM Briggs & Stratton part directly sourced from the manufacturer for us in Generators and Engines.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

It is a genuine replacement part which is supplied by the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This is the special screw which has multiple applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location...Read more and use of this hardware. It is a high-quality component which is made of durable metal and it is sold individually.

Ensure smooth and reliable operation of your generator with this genuine control panel assembly, designed to manage engine performance and provide precise control over essential functions. Built to meet OEM standards, this component simplifies operation while enhancing overall efficiency and durability. Ideal for replacing a worn or outda...Read moreted control board, it helps maintain equipment longevity and consistent performance. Installation is straightforward—disconnect power, remove the old panel, and secure the new one in place for dependable functionality.