04022 - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

This replacement oil filter is a genuine OEM sourced item commonly utilized on Briggs and Stratton engines that are commonly installed on lawn and garden equipment. This filter helps to remove harmful contaminants from engine oil that is needed for operation. This part is manufactured in accordance with applicable EPA emissions regulation...Read mores to maintain optimum engine performance. It is recommended to replace it at least once a season. Please note this oil filter is sold individually requiring a wrench to secure or remove it.

This is available as an individual replacement part and is made of flexible material. The Exhaust Gasket attaches to Muffler and helps to create a seal. If this part becomes broken it will need to be replaced and may require a wrench during the installation. It is an OEM Briggs & Stratton part directly sourced from the manufacturer for us in Generators and Engines.

This control panel is a critical component for maintaining the functionality of compatible Briggs & Stratton appliances. Designed to OEM specifications it ensures reliable response to user commands and supports proper operation of key functions. A malfunctioning panel may result in unresponsive buttons or inconsistent performance making t...Read moreimely replacement essential. Constructed from durable materials it offers long-term reliability and a secure fit. Installation should be performed with the appliance powered off and model compatibility must be verified prior to replacement.

The door hinge kit is sold as a set that contains all the necessary parts. They are made out of metal. These authentic items are supplied directly from the original equipment manufacturer for use with generators made by Briggs & Stratton. A screwdriver may be helpful when replacing these items. Over time these parts may break and will need to be replaced.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

It is a genuine replacement part which is supplied by the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This is the special screw which has multiple applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location...Read more and use of this hardware. It is a high-quality component which is made of durable metal and it is sold individually.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this pre-cleaner filter is to provide an additional layer of filtration for the air that is supplied in the engine. Over time it may wear out or ge...Read moret clogged eventually requiring a replacement. Keep in mind this high-quality component is made of durable foam material and is sold individually.

This is an authentic Andis replacement part. The black field screw is designed by the manufacturer for use in trimmers. This part is made of metal, and is generally used in securing the core/coil assembly. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct...Read more part. You will require a wrench when replacing this part. This item is sold individually.