03059 Briggs and Stratton Generator - Overview

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

A replacement support leg gives a portable generator a firm point of contact with the ground. It supports the frame and helps keep the unit steady during operation. A bent, cracked, worn, or missing leg can cause the generator to lean or rock. Made from durable material for regular outdoor use, the support leg is sold as one piece. A wren...Read morech set may be needed for installation. Check the equipment diagram before ordering to confirm the correct location and required hardware. Always turn off the engine, let the generator cool, and wear work gloves before beginning the repair.

This is an authentic Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with portable generators. The valve attaches to the bottom of the fuel tank and is used to regulate the fuel that exits the tank. This valve is priced as a single item.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This wheel is an authentic replacement part sourced directly from Briggs and Stratton. It is customarily used for portable generators. The purpose of this wheel is to reduce the amount of effort needed to transport the generator. This part is made of rubber and only includes one wheel. Please note the machine requires two.

This is an authentic Briggs & Stratton replacement part that is intended to be used with portable generators. The valve is used to connect the fuel line to the tank and to control the flow of fuel from the tank. This item is available as an individual replacement part.

The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.

This is an authentic Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with small engines. The gasket is used to seal the connection between the cylinder and the muffler. It is recommended to replace gaskets when servicing the engine to ensure proper seals when the parts are reassembled. This item is available as an individual replacement part.

This is a genuine replacement carbon brush which is supplied by the original equipment manufacturer for use with Briggs and Stratton portable generators. The purpose of the brush is to help conduct the current by maintaining physical contact with an armature inside the electric motor which powers the unit. It is a high-quality component w...Read morehich consists of a durable plastic holder and two carbon brushes with attached lead wires and springs.

The voltage regulator goes next to the cover. This is available individually and is made of durable materials. It is a genuine replacement part sourced from the original manufacturer for use with generators made by Briggs & Stratton. When replacing this item a screwdriver might be required during the installation process. It will require replacing if it becomes broken.

This is available as an individual replacement. The outlet is part of the control panel assembly. When replacing this item a wrench may be needed. It is made of metal and plastic and will need to be replaced if it becomes broken. This is an authentic Briggs & Stratton and Snapper replacement part that is sourced from the original manufacturer for use with generators.

The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or damaged, the nut and part may be loose and it should be replaced. Check your make, model and diagram to ensure you are choosing the correct part.