03045 Briggs and Stratton Generator - Overview

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

The OEM voltage regulator or voltage control is a part used to regulate the voltage so it can provide the right amount of power to electrical components. It attaches inside the alternator housing. The part is black and 2 x 3.5 inches. If damaged, the voltage will become too low/high and the part should be replaced. This part requires a vo...Read moreltmeter to use properly. Please refer to your make, model, and diagram to ensure this is the correct part.

This wheel is an authentic replacement part sourced directly from Briggs and Stratton. It is customarily used for portable generators. The purpose of this wheel is to reduce the amount of effort needed to transport the generator. This part is made of rubber and only includes one wheel. Please note the machine requires two.

This is an authentic Briggs & Stratton replacement part that is intended to be used with portable generators. The valve is used to connect the fuel line to the tank and to control the flow of fuel from the tank. This item is available as an individual replacement part.

The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

The circuit breaker attaches to the control panel and helps to stop overloads. This part is an OEM from Briggs & Stratton generators. This item is sold individually and is made of plastic and metal. A screwdriver might be required during the replacement of this part. It will require replacing if it breaks or burns out.

This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This detergent oil is warranty approved and specially compounded for warm weather use. Please note: it is important to avoid over filling your engine with oil.

This is a genuine manufacturer-sourced replacement part which is designed for use with Snapper and Briggs and Stratton portable generators. Over time batteries will become weaker and eventually will not provide enough power to operate the equipment as it was designed. Several factors can cause this, such as improper charging or the way th...Read moree unit is used along with normal deterioration of the battery. Note, this high-quality battery is sold individually. Refer to the owner's manual for the correct application.

The set exercise switch attaches to the hour meter. This is a genuine Briggs & Stratton part sourced directly from the manufacturer for use in generators. This part is available as an individual replacement. It is made of plastic and metal and may require a wrench during installation. It might become broken and will need to be replaced.

The metal screw attaches to the muff guard bracket. It is a genuine replacement part sourced from the original manufacturer for use with blowers, engines, generators, pressure washers, snowblowers, and vacuums made by Briggs & Stratton, Toro, and Lawn Boy. This item is available as an individual replacement part. When replacing this screw a wrench will be needed. It will need to be replaced if it strips or breaks.