030380-0 Briggs and Stratton Generator - Overview
Sections of the 030380-0
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$27.33
In Stock
Fuel Gauge Cap
PartSelect #: PS9314364
Manufacturer #: B4363GS
This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It i...
$58.31
On Order
Line-fuel
PartSelect #: PS9140673
Manufacturer #: 791745
This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to tra...
$16.54
In Stock
Solenoid
PartSelect #: PS9064363
Manufacturer #: 691656
A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acti...
No Longer Available
Wheel
PartSelect #: PS8914262
Manufacturer #: 209322GS
This wheel is an authentic replacement part sourced directly from Briggs and Stratton. It is customarily used for portable generators. The purpose of this wheel is to reduce the amount of effort neede...
No Longer Available
Brush Holder Assembly
PartSelect #: PS9157810
Manufacturer #: 91825GS
This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon b...
No Longer Available
E-ring
PartSelect #: PS10000220
Manufacturer #: 703977
The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.
$6.73
In Stock
Leg, Mounting
PartSelect #: PS10042739
Manufacturer #: B1764GS
This is a genuine part which is supplied directly from the original equipment manufacturer. This leg support is used to stabilize a Briggs and Stratton generator while it is in use. Please refer to t...
No Longer Available
Breaker, Circuit, 20a
PartSelect #: PS8914391
Manufacturer #: 202030GS
The circuit breaker attaches to the control panel and helps to stop overloads. This part is an OEM from Briggs & Stratton generators. This item is sold individually and is made of plastic and metal. A...
$128.96
In Stock
Switch, Set Exercise
PartSelect #: PS9160620
Manufacturer #: 87799GS
The set exercise switch attaches to the hour meter. This is a genuine Briggs & Stratton part sourced directly from the manufacturer for use in generators. This part is available as an individual repla...
$8.76
In Stock
Cover, Rbc Plastic With Cap
PartSelect #: PS8909587
Manufacturer #: 195422GS
This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/du...
$20.55
In Stock
Gasket-exhaust
PartSelect #: PS9295033
Manufacturer #: 695398
This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cy...
$12.20
In Stock
Common Symptoms of the 030380-0
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wouldn’t start.
I installed a new solenoid starter. Took me a total of 20 minutes. Started right up.
Parts Used:
-
Bruce from CARNATION, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
18 of 44 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!