030359-0 Briggs and Stratton Generator - Overview

The OEM voltage regulator or voltage control is a part used to regulate the voltage so it can provide the right amount of power to electrical components. It attaches inside the alternator housing. The part is black and 2 x 3.5 inches. If damaged, the voltage will become too low/high and the part should be replaced. This part requires a vo...Read moreltmeter to use properly. Please refer to your make, model, and diagram to ensure this is the correct part.

The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.

This Battery supplies power to a generator's electrical systems. It attaches inside the battery housing, which is usually mounted to the frame. It can be installed using a wrench set, and its installation is rated as "Easy" by customers. If the battery is unable to hold proper voltage or start the engine, it should be replaced. Refer to y...Read moreour make, mode,l and diagram to ensure this is the correct part for you. This battery is black, and made of plastic.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

The authentic 10" Wheel Assembly (Wheel, 10" Diameter) is a 10-inch black, plastic-and-ubber wheel. It allows easy moving of the generator. Installation requires pliers and is rated as "Easy". If your tire is flat, then it should be replaced. Refer to your make, model and diagram to ensure this is the right part.

This is a genuine Briggs & Stratton part sourced directly from the manufacturer for use in generators. The outlet is made of metal and plastic and attaches to the control panel. A screwdriver may be necessary during the installation of this item. It may become broken and will need to be replaced. This is available as an individual replacement part.

The circuit breaker is made out of plastic and metal. This authentic item is supplied directly from the original equipment manufacturer for use with generators made by Briggs & Stratton. This item is available as an individual replacement part. During the installation process, a screwdriver and a set of pliers might be needed to replace this part. It might break over time and will need replacing.

This is available as an individual replacement. The outlet is part of the control panel assembly. When replacing this item a wrench may be needed. It is made of metal and plastic and will need to be replaced if it becomes broken. This is an authentic Briggs & Stratton and Snapper replacement part that is sourced from the original manufacturer for use with generators.

The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or damaged, the nut and part may be loose and it should be replaced. Check your make, model and diagram to ensure you are choosing the correct part.

This is an OEM part sourced directly from the manufacturer. The circuit breaker boot is commonly found in portable generators from Briggs & Stratton. This part is made of high-quality plastic, and is placed in the control panel to help secure the circuit breaker. You may require a screwdriver when replacing this item. The circuit breaker boot is provided as an individual replacement part.