030324-0 Briggs and Stratton Generator - Overview

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

Frequently referred to as a Vibration Kit, this Vibe Mount Kit includes two durable rubber mounts, two metal washers, two bolts, and two locknuts. This kit is sourced directly from the manufacturer for use in pressure washers and attaches to the base of the unit to reduce vibration when the engine is on. When this part needs to be repla...Read moreced, you will notice more vibrations than normal coming from the unit. This part will become worn through regular use of the machine. You will need a socket set to complete this repair. Customers rate this repair as Easy.

This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replace...Read morement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover and gain access to the brush assembly • Take our old brushes and replace them with the new ones • Reassembly the cover

The circuit breaker attaches to the control panel and helps to stop overloads. This part is an OEM from Briggs & Stratton generators. This item is sold individually and is made of plastic and metal. A screwdriver might be required during the replacement of this part. It will require replacing if it breaks or burns out.

This fuel gauge cap is a genuine manufacturer-approved replacement part sourced directly from Briggs and Stratton. It is commonly used in portable generators to determine the amount of fuel left in the tank. This gauge is made of plastic, and it is sold individually. No tools are needed to install it. Simply discard the old gauge and replace with the new part.

This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/dust cap for easy access to the bearing. The cover acts as a barrier that prevents dirt and other contaminants from entering the bearing and p...Read moreotentially damaging it. It also protects the bearing from harsh environmental conditions and keeps it adequately lubricated. Over time, the cover may crack or break, leaving the bearing exposed. A faulty cover will result in several issues such as excessive noise and vibration, increased friction and wear, overheating, and lower overall equipment efficiency. To complete this repair, pry the center cap off first and then detach the old cover from the rear bearing. Clean the mating surface, align the new cover with the bearing, and snap the center cap into position.

This is an authentic item that is supplied directly from the original equipment manufacturer for Briggs and Stratton Generators. This kit includes one (1) female quick connect, one (1) Male quick connect, four (4) Clamps and the flexible rubber hose. This kit is used to connect the fuel lines to the fuel tank. It is recommended to install these parts in a well-ventilated area.

This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cylinder head. This special gasket is available as an individual replacement part, please see model diagram for associative parts.

This item is sold individually and is made of plastic. The fuel quick connect goes between the fuel line kit and the fuel valve. A set of pliers may be helpful when replacing this part. It will require replacing if it breaks. This is a Briggs & Stratton replacement part directly sourced from the manufacturer for use in portable generators.

It is an authentic item that is supplied by original equipment manufacturer, it is specially produced for use on Briggs and Stratton and Snapper generators. This kit is used to secure the engine to the main frame, it is designed to help reduce vibrations from a running engine. Over time the material may deteriorate and get compressed caus...Read moreing the generator to vibrate more than usual, if this happens replacing the mount should resolve the issue. It is a complete kit which includes one metal mount with a rubber pad, a screw, and three locknuts. Please note this replacement kit is sold individually.

This is an authentic Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with portable generators. The plastic wheel connects to the bottom of the frame and is used to provide mobility. This item is available as an individual replacement part.