030238-0 Briggs and Stratton Generator - Overview

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plus Toro snowthrowers and lawn tractors. This gasket is made of a flexible material and is priced individually. A screwdriver and a wrench may be needed to install this part.

This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replace...Read morement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover and gain access to the brush assembly • Take our old brushes and replace them with the new ones • Reassembly the cover

The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.

This is a genuine part which is supplied directly from the original equipment manufacturer. This leg support is used to stabilize a Briggs and Stratton generator while it is in use. Please refer to the owners manual for instructions on how to install or replace the leg support. This part is made of metal and is sold individually.

This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This detergent oil is warranty approved and specially compounded for warm weather use. Please note: it is important to avoid over filling your engine with oil.

The authentic 10" Wheel Assembly (Wheel, 10" Diameter) is a 10-inch black, plastic-and-ubber wheel. It allows easy moving of the generator. Installation requires pliers and is rated as "Easy". If your tire is flat, then it should be replaced. Refer to your make, model and diagram to ensure this is the right part.

This authentic OEM supplied trigger-throttle is designed for Briggs and Stratton and Snapper generators. It is designed to provide a user with a comfortable grip to operate the unit. This is an identical replacement for a damaged or a missing component that was installed on a new unit. Refer to the appropriate diagrams for your model to e...Read morensure the correct repair procedure. Keep in mind this high-quality handle assembly is made of durable material and is sold individually.

This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/dust cap for easy access to the bearing. The cover acts as a barrier that prevents dirt and other contaminants from entering the bearing and p...Read moreotentially damaging it. It also protects the bearing from harsh environmental conditions and keeps it adequately lubricated. Over time, the cover may crack or break, leaving the bearing exposed. A faulty cover will result in several issues such as excessive noise and vibration, increased friction and wear, overheating, and lower overall equipment efficiency. To complete this repair, pry the center cap off first and then detach the old cover from the rear bearing. Clean the mating surface, align the new cover with the bearing, and snap the center cap into position.

This is an authentic OEM sourced part which is specially made for DeWALT planers. It functions as a safety device. When the circuit becomes overloaded, this circuit breaker switch interrupts the transfer of electricity to the motor. Flip the switch on the circuit breaker to reset the connection. Please make sure to refer to the appropriat...Read moree diagrams for your model for the correct location and application of this component. Keep in mind this high-quality circuit breaker is sold as an individual item.

It is an authentic item that is supplied by original equipment manufacturer, it is specially produced for use on Briggs and Stratton and Snapper generators. This kit is used to secure the engine to the main frame, it is designed to help reduce vibrations from a running engine. Over time the material may deteriorate and get compressed caus...Read moreing the generator to vibrate more than usual, if this happens replacing the mount should resolve the issue. It is a complete kit which includes one metal mount with a rubber pad, a screw, and three locknuts. Please note this replacement kit is sold individually.