030227-0 Briggs and Stratton Generator - Overview
Sections of the 030227-0
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$27.33
In Stock
E-ring
PartSelect #: PS10000220
Manufacturer #: 703977
The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.
$6.73
In Stock
Battery
PartSelect #: PS8906971
Manufacturer #: 193463GS
This Battery supplies power to a generator's electrical systems. It attaches inside the battery housing, which is usually mounted to the frame. It can be installed using a wrench set, and its installa...
No Longer Available
Wheel
PartSelect #: PS8914298
Manufacturer #: 209636GS
The authentic 10" Wheel Assembly (Wheel, 10" Diameter) is a 10-inch black, plastic-and-ubber wheel. It allows easy moving of the generator. Installation requires pliers and is rated as "Easy". If your...
$113.48
In Stock
Mount, Vibration
PartSelect #: PS9308423
Manufacturer #: 87841GS
The OEM vibration mount is a black rubber part, which is used to prevent vibrations between the frame of the generator and the floor. It can be installed with a screw driver,and its installation is ra...
$6.40
In Stock
Outlet, 120/240V, 30A
PartSelect #: PS9359426
Manufacturer #: 204075GS
This is available as an individual replacement. The outlet is part of the control panel assembly. When replacing this item a wrench may be needed. It is made of metal and plastic and will need to be r...
No Longer Available
Nut, M8 Flange Serrated
PartSelect #: PS9293606
Manufacturer #: 67989GS
The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or da...
$6.40
In Stock
Assembly, Fold Down Handle
PartSelect #: PS9314280
Manufacturer #: B193200GS
The authentic fold down handle attaches onto the frame and allows you to pick up and more easily maneuver equipment. This assembly contains everything you will need to replace the entire handle. It ca...
$55.73
Special Order
Outlet, 120/125v, 15/20a
PartSelect #: PS9294308
Manufacturer #: 68759GS
This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It ...
$35.16
In Stock
Common Symptoms of the 030227-0
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!