030218-0 Briggs and Stratton Generator - Overview

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It is approximately 5.25 inches in length, while the head has a diameter of 3 inches. The purpose of the cap is to cover and protect the fuel ga...Read moreuge, which indicates the levels of gas available in the tank. It prevents dirt and debris from entering the gauge area and prevents fuel from leaking out. A faulty cap will allow contaminants to enter the gauge, and cause fuel to leak, leading to inaccurate fuel readings and safety risks. Twist the cap to remove it and clean the surrounding area thoroughly. Place the new gauge cap in position and ensure that it is locked in place.

The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plus Toro snowthrowers and lawn tractors. This gasket is made of a flexible material and is priced individually. A screwdriver and a wrench may be needed to install this part.

This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replace...Read morement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover and gain access to the brush assembly • Take our old brushes and replace them with the new ones • Reassembly the cover

This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/dust cap for easy access to the bearing. The cover acts as a barrier that prevents dirt and other contaminants from entering the bearing and p...Read moreotentially damaging it. It also protects the bearing from harsh environmental conditions and keeps it adequately lubricated. Over time, the cover may crack or break, leaving the bearing exposed. A faulty cover will result in several issues such as excessive noise and vibration, increased friction and wear, overheating, and lower overall equipment efficiency. To complete this repair, pry the center cap off first and then detach the old cover from the rear bearing. Clean the mating surface, align the new cover with the bearing, and snap the center cap into position.

It is an authentic item that is supplied by original equipment manufacturer, it is specially produced for use on Briggs and Stratton and Snapper generators. This kit is used to secure the engine to the main frame, it is designed to help reduce vibrations from a running engine. Over time the material may deteriorate and get compressed caus...Read moreing the generator to vibrate more than usual, if this happens replacing the mount should resolve the issue. It is a complete kit which includes one metal mount with a rubber pad, a screw, and three locknuts. Please note this replacement kit is sold individually.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or damaged, the nut and part may be loose and it should be replaced. Check your make, model and diagram to ensure you are choosing the correct part.

This connector is sourced from the original manufacturer as a replacement part for use in generators. The connector has 6 pins/terminals which allow the joining of various electrical cables and components in the generator. Over time the connector can break or wear down, rendering it unable to secure components together. This can result in...Read more electrical hazards, overheating, instability, and loose connections. Disconnect the wires/cables connected to the old connector and remove it from the housing. Place the new connector in the housing and reconnect the wires to the appropriate terminals, following the guidelines in your equipment manual.

This is an authentic Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with generator engines. The spark arrester screen connects to the muffler and is used to prevent embers from being discharged through the exhaust gasses. Over time the screen can become clogged from exhaust discharge and...Read more can inhibit the gasses from escaping. This item is available as an individual replacement part.