030209-2 Briggs and Stratton Generator - Overview
Sections of the 030209-2
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$27.33
In Stock
Line-fuel
PartSelect #: PS9140673
Manufacturer #: 791745
This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to tra...
$16.54
In Stock
Breaker, Circuit, 20a
PartSelect #: PS9919917
Manufacturer #: 209872GS
This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the elec...
$15.46
In Stock
Brush Holder Assembly
PartSelect #: PS9157810
Manufacturer #: 91825GS
This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon b...
No Longer Available
Wheel
PartSelect #: PS9269576
Manufacturer #: 197061GS
This is a genuine manufacturer-sourced replacement wheel which is specially designed for use with Briggs and Stratton and Snapper generators. It is an identical replacement for a missing or damaged wh...
$34.11
Special Order
Assembly, Handle
PartSelect #: PS8904965
Manufacturer #: 189715GS
This authentic OEM supplied trigger-throttle is designed for Briggs and Stratton and Snapper generators. It is designed to provide a user with a comfortable grip to operate the unit. This is an identi...
$70.74
In Stock
Kit, Mount,vibration, 45'.
PartSelect #: PS8908926
Manufacturer #: 197564GS
This is an OEM part sourced directly from the manufacturer. The vibration mount kit is commonly found in portable generators. This item includes the mounting bracket as well as a screw and three fla...
$17.29
Special Order
Cover, Rbc Plastic With Cap
PartSelect #: PS8909587
Manufacturer #: 195422GS
This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/du...
$20.55
In Stock
Gasket-exhaust
PartSelect #: PS9151797
Manufacturer #: 794818
This is an authentic Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with small engines. The gasket is used to seal the connection between the cylind...
$13.02
In Stock
Screw, M5 - .8 X 10 Taptite
PartSelect #: PS9116859
Manufacturer #: 74908GS
This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cov...
$6.40
In Stock
Common Symptoms of the 030209-2
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!