0238-1 Milwaukee Electric Drill - Overview

Genuine Milwaukee replacement part, this item is sold individually. This Chuck Key tightens the jaws of the 1/2 inch capacity Chucks on all the Drill models shown below. For convenience a Chuck Key Holder part number 48-66-4040 can be ordered. It is attached to the power cord then the Chuck Key is attached to it.

This is a genuine Milwaukee replacement part, it is sold individually. The purpose of the 06-75-3150 Screw is to secure the chuck to the spindle of the models listed below. This is a left hand threaded screw, to remove it turn it clockwise. We do have an article and video on

This authentic replacement part is designed for use with Milwaukee drills/drivers. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Bearings experience constant wear from pressure, heat,...Read more vibration and friction. Because of this, many bearings need to be periodically replaced. This part is made out of metal and it is sold individually.

Genuine Milwaukee replacement part Includes 1 Carbon Brush sold individually. Please go to the schematic listings for your tool to find the brush assembly parts compatible with this carbon brush and your tool. This carbon brush will fit a wide variety of Milwaukee tools. • Worn brushes are frequently the cause of a poorly running moto...Read morer. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

This cord protector is a genuine Milwaukee replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

It is an authentic manufacturer approved replacement item that is specially produced for Milwaukee drills. This metal bearing helps to secure intermediate pinion gear while allowing it to spin freely with minimal friction. Over time this part may wear out and restrict movement, if this happens it can easily be replaced. Please note this high quality item is sold individually.

This is a genuine Milwaukee part, it is sold individually. The chuck is the top portion of the drill that holds the different drill bits. It is compatible with a variety of drills listed below. If your drill's bit retention is suffering, the rotation feels stiff, or the chuck has seized up entirely, a new chuck should fix the problem. Thi...Read mores chuck is made of metal. To install this chuck, thread the new chuck assembly onto the spindle. Secure the chuck assembly as tightly as possible( by hand). Open the chuck to accept the retaining screw. Install the retaining screw and secure the screw with a Phillips screwdriver. The screw is reverse-threaded ( requiring counterclockwise rotation to secure.

This Milwaukee Quik-Lok-« cord is a genuine Milwaukee replacement part, it is sold individually.This is a two 8 foot cord for fast field replacement of a damaged cord.Made of premium grade Hi-Flex wire the cord is quickly removed and attached to Milwaukee tools with the Quik-Lok-« cord feature.To change a damaged cord simply turn the coll...Read morear at the top of the cord counter clockwise to loosen the nut and pull down on the cord to remove.To re-attach a new cord, line up the pins in the end of the tool with the pin receptacles in the end of the cord, push together and turn the collar clockwise to lock in place.

This is an authentic OEM sourced part which is specially designed for use with Milwaukee electric drills and drivers. The bearings are generally utilized to reduce the friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Un...Read morefortunately, over time components will wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-quality ball bearing is made of durable metal and is sold individually. Please make sure to refer to the appopriate diagrams of your model for the correct location and application of this hardware.