020490-00 Briggs and Stratton Pressure Washer - Overview

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plus Toro snowthrowers and lawn tractors. This gasket is made of a flexible material and is priced individually. A screwdriver and a wrench may be needed to install this part.

Sourced directly from the manufacturer, this part is used to open and release hot water if the water exceeds the maximum operating temperature. It has metal and plastic components, is not part of a kit or assembly, and is sold individually. When malfunctioning, the Thermo Relief Valve will open on a regular basis, which can cause damage ...Read moreto your pump. If it is opening often or on a regular basis, replace it to protect your pump from damage. You will need a socket set, a wrench set, and pliers to complete this repair. Customers rate this repair as Easy.

This is an authentic Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with portable generators. The valve attaches to the bottom of the fuel tank and is used to regulate the fuel that exits the tank. This valve is priced as a single item.

This filter, also known as a water inlet screen, is designed for use with pressure washers and has a 1-inch diameter (including the surrounding rubber housing). The filter itself is made of mesh and is sold as an individual part that filters dirt and debris from entering your pressure washer. It is recommended that this part is routinely ...Read moreinspected to keep your equipment running smoothly and to prevent a damaged filter from allowing dirt into your equipment. This part sits in-between the hose from your home and the pressure washer itself and is a genuine OEM part that requires no tools to replace or install.

This item is an authentic OEM sourced O-ring kit that replaces worn or damaged O-rings for the gun, hose and wand.Unfortunately, over time o-rings will wear out and they may begin to crack eventually requiring replacements. Refer to the appropriate diagrams for your model to ensure the correct replacement procedure. A screwdriver and a wr...Read moreench set might be needed to take apart and reassemble the equipment. Note, this kit is sold as an individual item.

This water inlet kit delivers a controlled supply of water into the appliance, supporting proper operation during use. Designed for dependable flow and secure connections, it is commonly replaced when water supply issues or leaks occur.

It is an OEM supplied Ez Start kit which is designed for Troy-Bilt and Briggs and Stratton pressure washers. This is a special mechanism which makes starting the engine easier by relieving pressure within the pump head. Unfortunately, over time components may wear out and begin to fail eventually requiring replacement to ensure your equip...Read morement runs properly. Note, this high-quality kit includes multiple parts, to ensure the correct application of these components, refer to the appropriate diagrams for your model. A wrench set will be needed to perform this repair.

This is a genuine replacement part that has been sourced from the original manufacturer to be used with generators and pressure washers from Briggs & Stratton and Snapper. The vibration mount fits between the engine and the frame assembly and is used to reduce vibration between the motor and frame. This item is sold as an individual replacement part.

This replacement part is used on the base of various models of pressure washers to reduce vibration from the pump. This Grommet has an O.D. of 1 inch, is not part of a kit or assembly, is sold individually, and is made of durable black rubber. This part is known to wear with regular use of your machine, it should be replaced if you noti...Read moreced more vibrations than normal within the unit. Customers rate this repair as Easy.

This is an original replacement part manufactured for use with pressure washers. This quick change nozzle delivers a 40-¦ angle spray for use with several pressure washing applications. The white quick change nozzle is sold as an individual replacement part.