Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
020429-1 Briggs and Stratton Pressure Washer - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
This is a genuine OEM sourced component which is specially designed for Craftsman pressure washers. It is an identical replacement for a missing or damaged outlet that was originally installed on a ne...
Used to connect the hose that supplies the chemical cleaning solution (soap), this OEM replacement Chemical Injection Kit consists of the brass fittings, a metal ball, a spring, and a rubber seal, and...
This is an authentic replacement part manufactured for use with pressure washers. This brass plug seals the valves in the manifold of the pump. The plug will come with the o-ring that seals the plug, ...
Sourced directly from the manufacturer, this part is used to open and release hot water if the water exceeds the maximum operating temperature. It has metal and plastic components, is not part of a ki...
Designed for use in various models of pressure washers, air compressors, and generators, this Woodruff Key is used to hold a shaft with a mating part, such as a gear. It is 1 inch in length, made of m...
This filter, also known as a water inlet screen, is designed for use with pressure washers and has a 1-inch diameter (including the surrounding rubber housing). The filter itself is made of mesh and i...
Frequently referred to as a Vibration Kit, this Vibe Mount Kit includes two durable rubber mounts, two metal washers, two bolts, and two locknuts. This kit is sourced directly from the manufacturer fo...
It is an OEM supplied Ez Start kit which is designed for Troy-Bilt and Briggs and Stratton pressure washers. This is a special mechanism which makes starting the engine easier by relieving pressure wi...
This replacement hose is a genuine OEM sourced item that specially produced for use with Craftsman pressure washers. This 25 ft. high-pressure hose is made of durable rubber with metal fittings and it...
This handle fastening kit includes two plastic thread wingnuts and two carriage bolts, which are essential for securely attaching the handle assembly to your pressure washer. The handle assembly is ty...
$8.11
In Stock
Order now and your part arrives by Apr 6
Questions And Answers for 020429-1
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I order the part from this site and received it within a week. the only problem was that spring was missing out of the sealed bag. NO PROBLEM!!! I cut a ball point pen spring to fit and everything works just fine. You just have to remember to put the spring in first, then the ball bearing and then the rubber o-ring.If you put them in back
... Read morewards you pressure will fed directly into your chemical container!!
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read morer /> used same technique to insert valve upward into bushing
