0200 - Overview

This short-style engine oil filter is designed to remove harmful contaminants from the oil while maintaining proper lubrication in pressure-lubricated small engines. Built with high-efficiency filtration media and internal safety features to support consistent oil flow, it helps reduce engine wear and protect internal components. Ideal fo...Read morer routine maintenance, it supports reliable performance and helps extend engine life during regular operation.

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal and is sold as an individual part. Screws will need to be replaced when they become stripped.

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.

This item is a genuine replacement part that has been OEM sourced and is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The rubber seal is used to prevent oil from leaking at the connection between the bottom of the oil fill tube and the crankcase. This item also allows the fill tube to firmly sit into the case. The dipstick tube seal if available as an individual replacement part.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This is an original part from Briggs & Stratton. The rocket cover gasket is compatible with many small engines. The cardboard composite gasket is designed to prevent damage to engine parts and absorb fuel leakage. A screwdriver and a wrench may be needed to make the removal and replacement. This part is sold individually. It is recommended to refer to engine manual and diagrams for further instruction.

This is a manufacturer approved replacement part used on a variety of lawn and garden equipment engines. This filter adds a second layer of protection against airborne-dirt particle ingestion. This is a foam pre-cleaner which is sold individually. Please note a paper filter and a cover are both sold separately. No tools are needed to rep...Read morelace this filter. • Remove the filter cover • Take out the old filter and replace it with a new one • Secure the top cover

This authentic manufacturer-sourced screw-taptite is made for use with Toro and Lawn-Boy lawn and garden equipment. It is an identical replacement for a missing or a damaged hardware that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the exact location and the correct application of this screw. It...Read more is made of durable metal and is sold as an individual item. A wrench will be needed to secure or remove it.

This is a genuine manufacturer-sourced part which is designed for use on lawn and garden equipment. It is an identical replacement for a missing or a damaged clamp that is used to secure the hose. Keep in mind this high-quality product is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams for your model for the correct location and application of this hardware.