01655-3 Briggs and Stratton Generator - Overview

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

Frequently referred to as a Vibration Kit, this Vibe Mount Kit includes two durable rubber mounts, two metal washers, two bolts, and two locknuts. This kit is sourced directly from the manufacturer for use in pressure washers and attaches to the base of the unit to reduce vibration when the engine is on. When this part needs to be repla...Read moreced, you will notice more vibrations than normal coming from the unit. This part will become worn through regular use of the machine. You will need a socket set to complete this repair. Customers rate this repair as Easy.

This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replace...Read morement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover and gain access to the brush assembly • Take our old brushes and replace them with the new ones • Reassembly the cover

This handle fastening kit includes two plastic thread wingnuts and two carriage bolts, which are essential for securely attaching the handle assembly to your pressure washer. The handle assembly is typically located where the handle connects to the main body of your machine. When these parts are broken, the handle will feel wobbly or loos...Read moree, and there may be visible damage to the mechanism. It is crucial to fix the assembly promptly, as a loose handle can pose safety risks and make it difficult to operate the pressure washer effectively. Please note that this genuine OEM kit is sold individually, and the handle itself is not included.

This fuel gauge cap is a genuine manufacturer-approved replacement part sourced directly from Briggs and Stratton. It is commonly used in portable generators to determine the amount of fuel left in the tank. This gauge is made of plastic, and it is sold individually. No tools are needed to install it. Simply discard the old gauge and replace with the new part.

This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/dust cap for easy access to the bearing. The cover acts as a barrier that prevents dirt and other contaminants from entering the bearing and p...Read moreotentially damaging it. It also protects the bearing from harsh environmental conditions and keeps it adequately lubricated. Over time, the cover may crack or break, leaving the bearing exposed. A faulty cover will result in several issues such as excessive noise and vibration, increased friction and wear, overheating, and lower overall equipment efficiency. To complete this repair, pry the center cap off first and then detach the old cover from the rear bearing. Clean the mating surface, align the new cover with the bearing, and snap the center cap into position.

This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cylinder head. This special gasket is available as an individual replacement part, please see model diagram for associative parts.

It is an authentic item that is supplied by original equipment manufacturer, it is specially produced for use on Briggs and Stratton and Snapper generators. This kit is used to secure the engine to the main frame, it is designed to help reduce vibrations from a running engine. Over time the material may deteriorate and get compressed caus...Read moreing the generator to vibrate more than usual, if this happens replacing the mount should resolve the issue. It is a complete kit which includes one metal mount with a rubber pad, a screw, and three locknuts. Please note this replacement kit is sold individually.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.