01655-2 Briggs and Stratton Generator - Overview
Sections of the 01655-2
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$27.33
In Stock
Line-fuel
PartSelect #: PS9140673
Manufacturer #: 791745
This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to tra...
$16.54
In Stock
Brush Holder Assembly
PartSelect #: PS9157810
Manufacturer #: 91825GS
This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon b...
No Longer Available
Cap, Fuel Gauge
PartSelect #: PS8903364
Manufacturer #: 189420GS
This fuel gauge cap is a genuine manufacturer-approved replacement part sourced directly from Briggs and Stratton. It is commonly used in portable generators to determine the amount of fuel left in th...
No Longer Available
Gasket-exhaust
PartSelect #: PS9295033
Manufacturer #: 695398
This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cy...
$12.20
In Stock
Kit,vibration Mount, 45'.
PartSelect #: PS9269331
Manufacturer #: 194150GS
It is an authentic item that is supplied by original equipment manufacturer, it is specially produced for use on Briggs and Stratton and Snapper generators. This kit is used to secure the engine to th...
No Longer Available
Outlet, 120/240V, 30A
PartSelect #: PS9359426
Manufacturer #: 204075GS
This is available as an individual replacement. The outlet is part of the control panel assembly. When replacing this item a wrench may be needed. It is made of metal and plastic and will need to be r...
No Longer Available
Kit,vibration Mount Hardware
PartSelect #: PS8908475
Manufacturer #: 192553GS
This is a genuine manufacturer sourced replacement anti-vibration mount which is specially designed for use with Briggs and Stratton and Troy-Bilt equipment. It is one of the mounts which helps to sec...
$18.74
Special Order
Outlet, 120/125v, 15/20a
PartSelect #: PS9294308
Manufacturer #: 68759GS
This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It ...
$35.16
In Stock
Common Symptoms of the 01655-2
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!