Models > 01643-0

01643-0 Briggs and Stratton Generator - Overview

Sections of the 01643-0

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve W/Bushing – Part Number: 192980GS
Fuel Valve W/Bushing
★★★★★
★★★★★
(5)
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$19.31
  In Stock
Breaker, Circuit, 20A – Part Number: 209872GS
Breaker, Circuit, 20A
PartSelect #: PS9919917
Manufacturer #: 209872GS
This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the elec...
$10.91
  In Stock
Wheel – Part Number: 197061GS
Wheel
PartSelect #: PS9269576
Manufacturer #: 197061GS
$24.02
  In Stock
Pin – Part Number: 703300
Pin
PartSelect #: PS10222315
Manufacturer #: 703300
  No Longer Available
Assembly, Handle – Part Number: 189715GS
Assembly, Handle
PartSelect #: PS8904965
Manufacturer #: 189715GS
$59.96
  In Stock
Nut, M8 Flange Serrated – Part Number: 67989GS
Nut, M8 Flange Serrated
PartSelect #: PS9293606
Manufacturer #: 67989GS
The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or da...
$4.99
  In Stock
Wheel Axle – Part Number: 93728GS
Wheel Axle
PartSelect #: PS9311204
Manufacturer #: 93728GS
$7.51
  Special Order
Outlet, 120/125V, 15/20A – Part Number: 68759GS
Outlet, 120/125V, 15/20A
PartSelect #: PS9294308
Manufacturer #: 68759GS
$27.56
  Special Order
Nut, Locking Hex M8 - 1.25 – Part Number: 52858GS
Nut, Locking Hex M8 - 1.25
PartSelect #: PS9003423
Manufacturer #: 52858GS
$3.99
  Special Order
Bearing – Part Number: 65791GS
Bearing
PartSelect #: PS9293149
Manufacturer #: 65791GS
$35.83
  On Order
Cap, Fuel – Part Number: 846987
Cap, Fuel
PartSelect #: PS11830156
Manufacturer #: 846987
$22.79
  In Stock
Receptacle, 6 Pin – Part Number: 22694GS
Receptacle, 6 Pin
PartSelect #: PS8927232
Manufacturer #: 22694GS
This connector is sourced from the original manufacturer as a replacement part for use in generators. The connector has 6 pins/terminals which allow the joining of various electrical cables and compon...
$5.90
  Special Order

Questions And Answers for 01643-0

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 01643-0

[Viewing 1 of 1]
Will Not Start
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
Fuel Valve W/Bushing
  • James from PICAYUNE, MS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers

install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole

install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
Parts Used:
Fuel Valve W/Bushing
  • Alan from RADFORD, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
Fuel Valve W/Bushing
  • John from LEES SUMMIT, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
5 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!