01150-1 Briggs and Stratton Generator - Overview
Sections of the 01150-1
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$27.33
In Stock
Inlet Needle, Seat, And Clip Assembly
PartSelect #: PS9052162
Manufacturer #: 631021B
$9.62
Special Order
Grommet,tank
PartSelect #: PS9307985
Manufacturer #: 83465GS
This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The m...
$6.40
In Stock
O-ring
PartSelect #: PS9050564
Manufacturer #: 632547
This O-ring is designed for use with small engine carburetors and is made of rubber, meaning over time and further exposure to fuel, it will become brittle and crack. This O-ring is installed within t...
$4.23
Special Order
Screw, M5 - .8 X 10 Taptite
PartSelect #: PS9116859
Manufacturer #: 74908GS
This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cov...
$6.40
In Stock
Rectifier, Battery Charge
PartSelect #: PS9054741
Manufacturer #: 65795GS
The battery charge rectifier goes inside the control box. It is an OEM from Briggs & Stratton for use in generators. This part is sold individually and is made of metal. A wrench and a screwdriver may...
No Longer Available
Nut, M8 Flange Serrated
PartSelect #: PS9293606
Manufacturer #: 67989GS
The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or da...
$6.40
In Stock
Outlet, 120/125v, 15/20a
PartSelect #: PS9294308
Manufacturer #: 68759GS
This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It ...
$35.16
In Stock
Tension Spring
PartSelect #: PS9051115
Manufacturer #: 630766
This is an authentic replacement part sourced directly from the manufacturer. The tension spring is commonly found in Toro snowthrowers. This part is made of metal, and is used to provide tension be...
$6.40
Special Order
Common Symptoms of the 01150-1
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!