Lawn Tractor Switches

Lawn Tractor Lawn Mower Ignition Switch

★★★★★

★★★★★

2 Reviews

This ignition switch is an OEM replacement part found near the steering wheel or dashboard in lawn tractors and riding mowers. The switch has four symbols on the top side which indicate its various functions including starting, stopping, running and reversing. The switch works by connecting/disconnecting the circuit between the battery and the ignition system. The switch can fail either from physical damage or faulty electrical wiring. If the ignition switch is no longer working, you will not be able to operate your equipment. To access the faulty switch, first disconnect the battery, and wiring harness. Squeeze the tabs on the sides of the switch and pull it out from its mounting position. Plug the new switch in place and ensure that the tabs are engaged. Finish the repair by reconnecting the wiring harness and battery. If your current key is in good working condition, you can continue to use it. However, if it is not, it is recommended to replace the key at the same time. Each ignition switch is sold individually.

Lawn Tractor Lawn Mower Power Take-off Switch

★★★★★

★★★★★

1 Review

This item is sourced from the original manufacturer. It is an authentic part used with riding lawn tractors/mowers. This is the switch that allows user to engage blades. To stop mower blades, place attachment clutch control in the "DISENGAGED" position. One (1) plastic switch is included per order. Mechanical switches tend to break with time, eventually requiring replacement. This is standard 8 terminal black switch. Replacing this switch is a simple task. • Make sure to disconnect spark plug • Once you gained access under the housing disconnect wires • Remove old switch by pushing on side tabs • Secure new PTO switch • Reconnect wires and spark plug • Test the unit

Lawn Tractor Switch Interlock This OEM-sourced interlock switch is a safety feature in your lawn equipment, designed to prevent accidents and injuries by stopping the machine from running if specific conditions are not met, such as when your foot is not pressing on the brake. It is typically located near the control panel, handle, or seat of the lawn mower. A faulty switch will cause the mower to fail starting, shut off when you are engaging the blades, or continue running without activating the safety features. Before replacing the switch, make sure the lawn mower is unplugged from its power source. Consult the user guide for instructions on accessing the switch. You may need a wrench or screwdriver to remove other components from the machine. Once you have located the switch, disconnect any wires and remove any fasteners holding it in place. Please note that this replacement part is sold individually.

Lawn Tractor Lawn Mower Ignition Switch This is an OEM sourced replacement ignition switch. It is commonly used on a variety of riding lawn mowers/tractors. Switch plays an important role because it allows user to easily start the mower using only a turn key. Because switches have mechanical internal parts, over time they will begin to fail requiring replacement. It has a plastic body and it is sold individually. Please note, the key is not included, it is sold separately. To replace this switch no tools will be needed. • Unplug the wires from an old switch • Remove the switch by squeezing tabs • Secure new switch in the opening • Reattach wires and test the new switch

Lawn Tractor Lawn Mower Interlock Switch It is a genuine manufacturer-approved part which is specially designed for Ryobi and Husqvarna riding lawn mowers and garden tractors. The purpose of the switch-interlock is to act as a safety feature which will shut the engine off when equipment is started or running in unsafe operating conditions. Unfortunately, over time parts will wear out and it may begin to fail eventually requiring a replacement. Refer to the owner\'s manual and the appropriate diagrams for your model for the correct location and installation of this component. Note, this high-quality plastic body interlock switch is sold individually. You will need a screwdriver to perform this repair.

Lawn Tractor Solenoid This solenoid is an authentic manufacturer replacement part for use in lawn tractors. It sends the electrical current from the battery to the motor to allow the tractor to start and run. The solenoid will need to be replaced if it is damaged or experiencing electrical failure. Signs of a failed solenoid include difficulties cranking the engine, hearing clicking or no sound at all when turning the ignition key, and a starter that cannot stop running. Begin the repair by disconnecting the battery for your safety. Take a note/picture of how the wire connectors are routed before disconnecting them. Remove the bolts that secure the solenoid in place and pull the faulty part out. Position the new solenoid in its place and secure it with the mounting bolts. Use your notes to reconnect the wiring and battery.

Lawn Tractor Lawn Mower Pto Push Switch It is a genuine manufacturer-sourced component which is specially made for use with Murray, Snapper and Simplicity riding lawn mowers and garden tractors. It is the part of the equipment that allows a user to engage and disengage the blades. Unfortunately, over time components will wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-quality plastic body switch is sold individually. Please make sure to refer to the owners manual and the appropriate diagrams of your model for the correct location and application of this part.

Lawn Tractor Switch, Pto This PTO switch is an authentic manufacturer-supplied part which is made for use with Husqvarna riding lawn mowers and garden tractors. When pressed, it engages the clutch to turn the blades. Over time it may begin to malfunction or get damaged eventually requiring a replacement to ensure your equipment operates properly. Make sure to refer to the appropriate diagrams and the owner's manual for the exact location and the correct repair procedure. One durable plastic body PTO switch is sold individually. The switch is secured in the housing by two tabs on each side of the component. Replacing it is a simple task that does not require any tools.

Lawn Tractor Switch-ignition This is an authentic replacement part sourced from the original manufacturer for use with Toro lawn tractors and riding mowers. The ignition switch goes next to the hour meter. If this part becomes broken it will need to be replaced and may require a screwdriver during the installation. This part is available individually and is made of plastic and metal.

Lawn Tractor Switch Assembly, Ignition, 6 Pin Indak

★★★★★

★★★★★

1 Review

Sold as a kit, including the metal body switch, a pair of keys, and the required hardware, this Ignition Switch Assembly has been sourced directly from the original manufacturer. If you are unable to start and stop your engine, you may need to replace the Ignition Switch Assembly. To complete this repair, you will need a screwdriver, a wrench set, and pliers. Customers rate this repair as Easy.