KitchenAid Freezer Hardware

Your Price

$7.47

KitchenAid Freezer Screw

PartSelect Number PS11743743

Manufacturer Part Number WP681249

Sold individually.

Your Price

$7.47

KitchenAid Freezer Screw

★★★★★

1 Review

PartSelect Number PS11742721

Manufacturer Part Number WP488729

Metallic screw that is less than an inch long. Does not include the plastic washer.

Installation Instructions

Kyle from Wimauma, FL

Black Cam was bren on lower door hinge

This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder. Read more...

Your Price

$7.47

KitchenAid Freezer Refrigerator Screw

★★★★★

2 Reviews

PartSelect Number PS11747542

Manufacturer Part Number WP98165

This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.

Installation Instructions

Lynn H from MILL CREEK, WA

Hinge pin for drawer lid broke

1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the securing slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed. Read more...

Your Price

$9.62

KitchenAid Freezer Screw

PartSelect Number PS11748983

Manufacturer Part Number WPW10141645

Your Price

$7.47

KitchenAid Freezer Dryer Screw

★★★★★

1 Review

PartSelect Number PS11743744

Manufacturer Part Number WP681414

This screw is sold individually.

Installation Instructions

Pamelia from LA CROSSE, VA

Our washer was purchased 1/6/2006 and it started banging and walking out of its place when the washer started into the spin cycle. This would occur no matter the size of the load.

We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempted to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??

Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently! Read more...

Your Price

$11.77

KitchenAid Freezer Transformer Screw

PartSelect Number PS11742722

Manufacturer Part Number WP488787

This screw is sold individually. It is a genuine OEM replacement part, and it is designed for use with refrigerators. Most often it is used with the ice bucket ice deflector, retainer clip, and front cover. Due to varied uses we recommend referring to model-specific diagrams for exact placement. This screw measures 8-18 by 1/2 inch.

Your Price

$7.47

KitchenAid Freezer Refrigerator Single Hex Head Screw

PartSelect Number PS11742731

Manufacturer Part Number WP489069

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

Installation Instructions

Chris from Pompano Beach, FL

Water in bottom of dishwasher

Disconnected power. Shut off water supply. Took off the front, disconnected copper supply line and flexible water line, removed water inlet valve. Took elbow from old inlet valve and put in on new one. Put new valve in, reconnected water lines, put back front panel. Opened water supply, Flipped breaker back on. Done and it worked! Read more...