Jonsered Brush Cutter Filters
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Jonsered Brush Cutter Filters
Your Price
$9.62
In Stock
Jonsered Brush Cutter Engine Fuel Filter
PartSelect Number PS9285148
Manufacturer Part Number 530095646
This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filter is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.
Fixes these symptoms
- Engine stops after a few seconds or minutes
- Will Not Start
- See more...
Installation Instructions
Mark from LYNDONVILLE, NY
Deterioration of fuel line system
Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark
Read more...
Your Price
$14.43
In Stock
Jonsered Brush Cutter Chainsaw Fuel Filter
PartSelect Number PS12661913
Manufacturer Part Number 591375401
This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article and video on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.
Your Price
$6.72
In Stock
Jonsered Brush Cutter Trimmer Filter
PartSelect Number PS9005902
Manufacturer Part Number 530150253
The air filter prevents dirt and debris from entering the engine on your lawn equipment. This is an OEM filter that is white, roughly 2x3.5 inches in dimension, and can only be purchased individually. Made of foam, the air filter becomes clogged and worn over time, causing the engine to run rough from restricted air flow.
You can make this repair easily with no required tools by inserting the new filter inside the air cleaner housing of your engine.
Your Price
$8.01
In Stock
Jonsered Brush Cutter Trimmer Oiled Air Filter
PartSelect Number PS9020811
Manufacturer Part Number 537186301
This ready-oiled air filter is an OEM part that traps dirt and debris, preventing them from entering the engine. This part is black, comprised of foam, and is sold individually. Your air filter may become dirty and clogged over time, and because it is oiled, it is difficult to wash because it is oiled, so it will need to be replaced. A clogged air filter will cause your engine to run rough from restricted air flow.
This is an easy repair to make and does not require any special tools.
Your Price
$10.94
In Stock
Jonsered Brush Cutter Trimmer Air Filter
PartSelect Number PS8993617
Manufacturer Part Number 502198602
This replacement air filter is a genuine item, not an aftermarket imitation. It is specially designed for use on Husqvarna handheld lawn and garden equipment. Its purpose is to filter out dust and debris from contaminating the carburetor and the engine. Please note, this foam air filter is sold individually. To replace this air filter no special tools would be needed. • Remove the air filter cover • Remove the old air filter • Secure the new air filter • Reattach the cover
Your Price
$16.03
In Stock
Jonsered Brush Cutter Filter
PartSelect Number PS9021729
Manufacturer Part Number 537337201
This is a genuine part that is supplied by the original manufacturer for use with Husqvarna brush cutters. The air filter cleans the air entering and exiting the carburetor. This part is a common wear item, we recommend replacing the air filter periodically. For this repair, you will need a pair of pliers and a screwdriver to remove any covers or shrouds.
Your Price
$19.26
In Stock
Jonsered Brush Cutter Filter Holder
PartSelect Number PS8991716
Manufacturer Part Number 503890301
It is a genuine item that is supplied directly from the original equipment manufacturer for use with Husqvarna handheld lawn and garden equipment. This is the special component that is used to secure the air filter, it provides an identical replacement for a missing or damaged part that came with the new equipment. It is a high-quality holder which is made of durable plastic and is sold individually.
Your Price
$11.25
In Stock
Jonsered Brush Cutter Filter
PartSelect Number PS9030038
Manufacturer Part Number 537427101
The filter is an OEM direct from Husqvarna and is specially designed for use on a Brushcutter. This part prevents dirt and debris from entering the engine which can prevent the unit from running as it should. It is recommended to regularly check the filter and clean it and replace when needed. This part is made of foam and is sold separately.
Your Price
$24.08
In Stock
Jonsered Brush Cutter Filter
PartSelect Number PS11824016
Manufacturer Part Number 574668003
This is an authentic Husqvarna replacement part that has been sourced from the original manufacturer to be used with brushcutters. The filter fits into the air cleaner base and is used to prevent contaminants from entering the engine\\\'s intake. The air filter is sold as an individual replacement part. A screwdriver may be needed to install this part.
Your Price
$8.01
In Stock
Jonsered Brush Cutter Fuel Inlet Screen
PartSelect Number PS8990124
Manufacturer Part Number 503481301
Related Jonsered Brush Cutter Parts
- Jonsered Brush Cutter Brackets and Flanges
- Jonsered Brush Cutter Carburetors
- Jonsered Brush Cutter Handles
- Jonsered Brush Cutter Hardware
- Jonsered Brush Cutter Hoses and Tubes
- Jonsered Brush Cutter Manuals and Literatures
- Jonsered Brush Cutter Seals and Gaskets
- Jonsered Brush Cutter Springs and Shock Absorbers
- Jonsered Brush Cutter Starters
- Jonsered Brush Cutter Transmissions and Clutches