Homelite Edger Hardware

Homelite Edger Bolt This is a genuine item that is supplied directly from the original equipment manufacturer for use with lawn and garden equipment. It is an identical replacement for a missing or a faulty bolt that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

Homelite Edger Flanged Washer

★★★★★

★★★★★

1 Review

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

Homelite Edger St Screw , Steel M4 L= 14mm Bl This part is an OEM from Ryobi. The screw (m4 x 14mm bl) is compatible with a variety of lawn and garden tools. The metal screw is often used to help secure the housing assembly. This item is sold individually, and a hex key is required for the installation. It is encouraged to purchase spares, as they can wear over time and regular use.

Homelite Edger Screw (1/4-20 X 1-1/4 In.) It is a genuine item that is supplied directly from the original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. This is the special screw which is utilized to secure the gear head, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this durable metal hex head screw is sold individually, you will need a wrench to secure or remove it.

Homelite Edger Push Nut This part is available as an individual replacement. The push nut attaches to the wheel and is made of plastic. When replacing this item a set of pliers and a hammer may be needed. It will need to be replaced if it becomes broken. This is an authentic Homelite and Ryobi replacement part that is sourced from the original manufacturer for use with trimmers and edgers.

Homelite Edger Cupped Washer The cupped washer attaches to the tri-arc blade with the use of the lock nut. This part is an OEM from Ryobi and Homelite to be used in brushcutters and trimmers. It is made of metal and helps to keep the cutting tool in place. A wrench will be needed if this part needs to be replaced. This washer is priced as an individual replacement part.

Homelite Edger Clamp, Fuel Line This fuel line clamp is sourced from the original manufacturer for use in edgers. It is a metal clamping device with a diameter of approximately 1/3 of an inch, placed around the fuel line to keep it secured against the fuel tank/carburetor and prevent fuel from leaking. Over time the clamp can corrode, crack, or become loose. This issue should be addressed promptly as a faulty clamp will cause fuel to leak, allow air to enter the fuel system leading to a lean fuel mixture, and allow contaminants to enter and clog the fuel system. To complete the replacement, use a pair of pliers to squeeze the clamp and slide it off the line. Place the new clamp on the fuel line and tighten it. Avoid over tightening as this will place excessive pressure on the fuel line.

Homelite Edger Screw, St3.5x12.7

Homelite Edger Nut, M12x1.25 In your edger, this nut attaches the cutting blade to the drive shaft assembly. Having a 12-millimeter diameter and a thread pitch of 1.25mm, it secures the blade so that you can effectively cut through grass, weeds, or other vegetation. A broken nut becomes loose during operation, disengaging the cutting blade. You may also notice that it is cracked, fractured, or its threads have been stripped. If a damaged nut is not replaced, you will experience uneven trimming. This also poses a safety concern as injuries may happen if the blade detaches during operation. To remove this nut from your machine, you need to immobilize the blade using a blade lock so it does not rotate. Using a wrench or a socket, loosen the nut by turning it counterclockwise. You can then continue to unscrew it by hand before removing it from the blade completely. Before adding this OEM replacement part to your cart, please keep in mind that this nut is sold individually and separately from the cutting blade.

Homelite Edger Nut, M12x1.25 This is a genuine Powermate replacement part sourced directly from the manufacturer. The nut is generally found in lawn edgers. This is a metal part that is used to secure the ends of the drive shaft and hold it to the blade arm. Please be aware that there are different nuts used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this part. This item is sold individually.