Generator Hardware

Generator Torx Screw Genuine OEM replacement part, this item is sold individually. This screw is used in various places in all of the tools listed below The most common use for this screw is to secure plastic housings together. It has a Torx T-20 head.

Generator Bolt This is a genuine component which is specially designed for use with Honda engines commonly installed on lawn and garden equipment. It is supplied directly from the original equipment manufacturer. This bolt-stud helps to mount the cover-fan and the pull-starter. Please make sure to refer to the appropriate diagrams of your model for the correct application of this hardware. Keep in mind this high-quality bolt-stud is made of durable metal and is sold individually. Replacing it is a simple task that should only require a wrench set to remove the old and secure the new.

Generator Grommet, Drain Cock This is an OEM part sourced directly from the manufacturer, sold individually. The grommet is inserted into the fuel tank of the generator to hold the fuel drain cock, which can be shut off to stop the flow of fuel, or opened to allow the fuel to flow to run the generator. No tools are required for installation. Part is compatible with the models listed below.

Generator Washer-lock 5/16 This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you need this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

Generator Flange Nut This genuine Honda flange nut is generally used to secure fan or starter housing to the main unit. It is an authentic item sourced from original equipment manufacturer for use with small engines. It is a hex flange nut which would require a wrench fro installation. Please note this item is sold individually.

Generator Bolt, Flange 6x10 This OEM-manufactured flange bolt provides a secure connection between two parts of your equipment. What is different about a flange bolt is that it has a wide, flat flange at the end. This helps to distribute the load being applied to it and prevents the bolt from becoming loose. Flange bolts are commonly found in lawn equipment, but their location varies by the make and model of the machine. When damaged, the part that the flange bolt was holding may loosen and fall off. You also may observe that it the flange bolt is cracked or corroded. It is important for you to replace broken flange bolts immediately as loose or vibrating parts can detach from your equipment while it is operating. You need a socket wrench to remove a flange bolt, as well as rust dissolver or penetrating oil if it is stuck. This replacement part is sold individually so make sure that you consult your user guide to identify where your flange bolts are and how many your equipment needs.

Generator Bolt- Flange - 6x79 Ct200 This bolt helps to secure muffler and carburetor to the short block. It is sourced from original equipment manufacturer for use with Honda small engines. Usually this bolt would need replacement if it is lost or has stripped threads. Please note this is a hex head bolt requiring a wrench for installation. It is sold individually.

Generator Nut-self-lock- 6mm This manufacturer-approved nut is supplied by the original manufacturer for use with Honda engines that are commonly installed on lawn and garden equipment. It is a standard hardware which may have multiple applications. Make sure to refer to the appropriate diagrams for your model to ensure the exact location and the correct application of this part. This high-quality nut is made of durable metal and is sold individually. A wrench will be needed to secure or remove it.

Generator Pin, 3/32 X 1.6 The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

Generator Key-flywheel

★★★★★

★★★★★

1 Review

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.