Generator Caps and Lids

Generator Gasket-rocker Cover This is an original part from Briggs & Stratton. The rocket cover gasket is compatible with many small engines. The cardboard composite gasket is designed to prevent damage to engine parts and absorb fuel leakage. A screwdriver and a wrench may be needed to make the removal and replacement. This part is sold individually. It is recommended to refer to engine manual and diagrams for further instruction.

Generator Collar- Fan Cover This collar is an authentic manufacturer-supplied part which is specially made for Honda engines commonly installed on a variety of lawn and garden equipment. It is an identical replacement for a faulty or a missing hardware that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the exact location and the correct application of this component. A wrench set will be needed to secure or remove the hardware that holds this part. This high-quality collar is made of durable metal and is sold as an individual item.

Generator Cap Assembly- Noise Suppressor The noise suppressor cap assembly, also known as the spark plug cap/boot is responsible for connecting the spark plug to the ignition coil, and helping to reduce the amount of noise created when running outdoor power equipment. This OEM replacement part includes a rubber cap with a metal contact inside. It is found at the end of the spark plug wire and has a threaded center shaft which allows you to easily screw it into position. Over time the metal contact may corrode, or the cap may dry out and crack or break. If your equipment is misfiring, running poorly, or has interference with other electronic equipment, the cap assembly likely needs to be replaced. To remove the old cap assembly, use your fingers or a set of pliers to carefully pull it off the end of the wire. Place the new cap assembly onto the end of the wire and fasten it securely. Please note this part is sold individually.

Generator Fuel Gauge Cap

★★★★★

★★★★★

2 Reviews

This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It is approximately 5.25 inches in length, while the head has a diameter of 3 inches. The purpose of the cap is to cover and protect the fuel gauge, which indicates the levels of gas available in the tank. It prevents dirt and debris from entering the gauge area and prevents fuel from leaking out. A faulty cap will allow contaminants to enter the gauge, and cause fuel to leak, leading to inaccurate fuel readings and safety risks. Twist the cap to remove it and clean the surrounding area thoroughly. Place the new gauge cap in position and ensure that it is locked in place.

Generator Cap-spring It is an OEM component which is designed for Briggs and Stratton engines that are commonly installed on a variety of lawn and garden equipment. The cap helps to secure the spring in the pump. Over time it may wear out, get damaged or lost eventually requiring a replacement. To ensure the exact location and the correct application of this hardware, refer to the appropriate diagrams of your specific model. This high-quality cap-spring is made of durable metal and is sold as an individual component. You may need a screwdriver and a wrench set to perform this repair.

Generator Screw Hhsfc M6-1 X 31 Bp&o It is a genuine item that is supplied directly from the original equipment manufacturer for use with Generac portable generators. The bolt helps to secure the cover. This is a high-quality replacement for a missing or a damaged hardware that was originally installed on a new unit. Please make sure to check the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality cover bolt is made of durable metal and is sold individually. A wrench will be needed to secure or remove it.

Generator Cap Fuel W/gauge 6

★★★★★

★★★★★

1 Review

This is an authentic Powermate replacement part manufactured for use with generators. This fuel cap includes a tether and is used to seal the fuel tank. The fuel cap is sold individually, please see model diagram for associative parts.

Generator Cover-air Cleaner

★★★★★

★★★★★

1 Review

This air cleaner cover is a genuine manufacturer approved replacement part that is specially designed for Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. The purpose of this cover is to secure and protect the air filter element which is sold separately. It is made from durable plastic and it is sold individually. Replacing this part does not require any tools.

Generator Cover-air Cleaner This is an authentic Briggs & Stratton replacement part, sourced from the original manufacturer for use with small engines. The special air cleaner cover is commonly used to secure the air filter to the air cleaner base. This air cleaner cover is available as an individual replacement part, please see model diagram for associative parts.

Generator Cap Fuel Tank This high quality replacement cap is an authentic OEM sourced item that is designed for use with generators. It is designed to keep the fuel in the tank. This fuel cap is made from durable plastic and it is sold individually.