Dust Collector Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dust Collector Hardware
Your Price
$6.25
In Stock
Dust Collector Washer 5/16 Std Flt
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
PartSelect Number PS16381824
Manufacturer Part Number 596134901
It is an authentic item that is supplied directly from the original equipment manufacturer for use with Husqvarna and Poulan lawn and garden equipment. A washer is generally utilized to provide a tight seal between connected parts, over time it may wear out or simply get lost eventually requiring a replacement. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this durable metal washer is sold individually.
Installation Instructions
robert from EUREKA, CA
transaxle rotated forward on 2015 Husqvarna YT42DXLS
2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair. HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Your Price
$6.25
In Stock
Dust Collector Screw
PartSelect Number PS10169702
Manufacturer Part Number 330019-14
It is a genuine replacement screw that is sourced directly from original equipment manufacturer. This is a standard hardware that has multiple uses depending your tool. For correct location and use of this screw, please check appropriate diagrams. This torx screw is sold individually.
Your Price
$6.25
In Stock
Dust Collector Washer-15x7.3x1.6
PartSelect Number PS16381860
Manufacturer Part Number 596204101
This item has been sourced from the original manufacturer to be used with tillers and riding lawnmowers from Husqvarna and Poulan. This metal washer is used to provide spacing or to disperse pressure put on a part assembly across a wider surface area. It is recommended to review your model\\\'s diagram to verify the washer\\\'s usage and compatibility. This item is sold individually.
Your Price
$12.50
In Stock
Dust Collector Key
PartSelect Number PS10318424
Manufacturer Part Number 1343758
This is a genuine OEM replacement part, it is sold individually. This Key is needed to operate all of the models listed below. It is inserted into the switch to make it possible for the machine to turn on. It can be removed for the purpose of unauthorized use of the machine.
Your Price
$6.25
On Order
Dust Collector Screw
PartSelect Number PS10169693
Manufacturer Part Number 330019-03
This replacement screw is an authentic OEM sourced item, not an aftermarket equivalent. This is screw is used in a lot of different applications depending on your tool. Please check appropriate diagrams for correct use and location of this screw. This pan head screw is sold individually. You will need a torx screwdriver when working with this hardware.
Your Price
$6.25
In Stock
Dust Collector Tapping Screw 4x18
PartSelect Number PS9931581
Manufacturer Part Number 266326-2
This tapping screw is an authentic hardware that is supplied by original tool manufacturer for use with a variety of Makita power tools. It has multiple uses depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this screw. Note this durable metal screw is sold individually.
Your Price
$8.47
In Stock
Dust Collector Flat Head Screw M5
PartSelect Number PS10145048
Manufacturer Part Number 265008-3
This is an authentic OEM sourced item designed for use with Makita compound miter saws. This flat head screw is used to secure the center cover which is sold separately. Please note, one metal screw is included per order. You will need a Phillips head screwdriver to install or remove this hardware.
Your Price
$55.03
In Stock
Dust Collector Snap Ring
PartSelect Number PS10458281
Manufacturer Part Number 331038
This is a genuine manufacturer-sourced component which is specially designed for use with Jet and Powermatic dust collection systems. It is an identical replacement for a missing or a faulty snap ring that was included with a new unit. The ring helps to secure a dust bag, please make sure to check the appropriate diagrams and the owners manual for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable material and is sold individually.
Your Price
$34.25
In Stock
Your Price
$10.12
In Stock
Dust Collector Flat Washer, M8
PartSelect Number PS10517157
Manufacturer Part Number TS-1550061
This manufacturer-sourced replacement flat washer is an authentic hardware which is specially designed for use with power tools. Its purpose is to help distribute the pressure evenly between connected parts, this washer has multiple applications depending on the model of our unit, make sure to check appropriate diagrams for correct location and use. This part is made of high-quality metal and it is sold individually.