DeWALT Impact Driver Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular DeWALT Impact Driver Parts
Your Price
$23.83
In Stock
DeWALT Impact Driver Housing Assembly
PartSelect Number PS12508695
Manufacturer Part Number N413423
This OEM housing assembly in your impact driver is the protective outer casing that encloses the internal components of the tool, providing structural support. The assembly consists of both the top and bottom sides and it operates using a 20-volt battery. To identify if the housing assembly is broken, look for visible cracks, fractures, or loose components. Excessive vibration or unusual noises during operation can also indicate a problem. To replace the housing assembly, remove all the screws and separate the case. Transfer all the components from the old case to the new one, ensuring switches like the forwards and reverse switch and power settings are properly aligned. Then, reassemble the case by putting all the screws back in using a screwdriver with a Torx bit. Note that the screws are sold separately from the housing.
Your Price
$6.40
In Stock
DeWALT Impact Driver Drill Compression Spring
PartSelect Number PS11929418
Manufacturer Part Number N078434
This compression spring is for drills.
The compression spring holds tension against the anvil and sleeve to keep the anvil tight on the armature.
Disconnect the power before installing this part. Wear work gloves to protect your hands.
Your Price
$6.40
In Stock
DeWALT Impact Driver Steel Ball
PartSelect Number PS11929439
Manufacturer Part Number N089668
Genuine Dewalt replacement part, this item is sold individually. The N089668 Steel Ball is part of the chuck assembly of the Impact Drivers shown below. When you pull back the sleeve of the chuck assembly and insert your bit, the Steel Ball is the part that locks the bit in the chuck assembly.
Your Price
$6.40
In Stock
DeWALT Impact Driver Compression Spring
PartSelect Number PS11929265
Manufacturer Part Number N019351
This is an OEM authorized part. It is sold individually. This spring maintains pressure on the N078437 Sleeve, and the rest of the bit holder assembly, to keep the bit in the holder. If this part fails the bit cannot be held in the bit holder. It is commonly used in impact drivers, and is compatible with the impact drivers listed below.
Your Price
$9.86
On Order
DeWALT Impact Driver Carbon Brush With Lead
PartSelect Number PS10183918
Manufacturer Part Number 655213-02
Genuine DeWalt replacement part rnIncludes 1 Carbon Brush with wire lead in rubber sheath attached.rn • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
Your Price
$11.70
In Stock
DeWALT Impact Driver Carbon Brush With Spring
PartSelect Number PS10173724
Manufacturer Part Number 450374-12
Genuine OEM replacement This brush is sold individually, 2 are needed for most every electric power tool It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Your Price
$6.40
On Order
DeWALT Impact Driver Spring
PartSelect Number PS12527474
Manufacturer Part Number N437890
This is a spring designed to fit within the bit holder assembly of an impact driver, also known as an impact wrench. Positioned between the anvil and ring gear, this spring is accompanied by a washer and hog ring on each side to provide tension and maintain consistent pressure on the inserted bit within the holder. As a high-wear component, this spring will eventually wear out, resulting in a less secure grip on the bit by your driver and its hammer mechanism. This spring is equipped with a hook for secure attachment within the main housing. If the hook becomes damaged or misshapen, the entire spring will need replacement. To replace this spring, you will require a screwdriver and must partially disassemble the primary driver housing to access it.
Your Price
$6.40
In Stock
DeWALT Impact Driver Plain Washer
PartSelect Number PS11929226
Manufacturer Part Number N016823
This is a genuine OEM part sourced from the manufacturer. Sold individually. Washer provides a bearing surface for fastener load distribution or acts as a spacer. Is used in a number of impact drivers, listed below.
Your Price
$6.40
In Stock
DeWALT Impact Driver Hog Ring
PartSelect Number PS11929390
Manufacturer Part Number N053863
This is an authentic OEM replacement part, sold individually. The Hog Ring holds the bit holder assembly together, it is inserted in the very front of the sleeve. Without it the complete bit holder assembly would completely fall apart. Screwdriver is needed for repair. Compatible with the impact drivers listed below.
Your Price
$6.40
In Stock
DeWALT Impact Driver Hog Ring
PartSelect Number PS11927770
Manufacturer Part Number 608114-00
This is an authentic OEM replacement part used on Dewalt Impact Wrenches. This part is made out of Metal and it is Sold Individually. The Hog Ring sits on the end of Anvil. Screwdriver is needed for repair.
DeWALT Impact Driver Appliance Types
Popular DeWALT Impact Driver Models
Below are the most popular DeWALT Impact Driver models we have. Enter your model number in the search box to find your model.
- DCF885B 20v Impact Driver
- DCF885B 20v Impact Driver
- DCF885B 20v Impact Driver
- DCF885B 20v Impact Driver
- DCF809C2 Impact Driver
- DCF809C2 Impact Driver
- DCF809C2 Impact Driver
- DCF887B 20v 3 Spd Impa Drivr
- DCF887B 20v 3 Spd Impa Drivr
- DCF887B 20v 3 Spd Impa Drivr
- DCF900B Impact Driver
- DCF885C2 20V Impact Driver
- DCF885C2 Impact Driver
- DCF885C2 Impact Driver
- DCF891B Impact Driver
- DW292 1/2 Impact Wrench
- DCF840B Impact Driver
- DCF899HB Impact Driver
- DW056 18V Cordless Impact Driver
- DCF883B 20V 3/8 Impact Wrench