Craftsman Impact Driver Parts

This is an OEM authorized part. It is sold individually. This spring maintains pressure on the N078437 Sleeve, and the rest of the bit holder assembly, to keep the bit in the holder. If this part fails the bit cannot be held in the bit holder. It is commonly used in impact drivers, and is compatible with the impact drivers listed below.

Genuine Dewalt replacement part, this item is sold individually. The N089668 Steel Ball is part of the chuck assembly of the Impact Drivers shown below. When you pull back the sleeve of the chuck assembly and insert your bit, the Steel Ball is the part that locks the bit in the chuck assembly.

Genuine DeWalt replacement part rnIncludes 1 Carbon Brush with wire lead in rubber sheath attached.rn • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Genuine OEM replacement This brush is sold individually, 2 are needed for most every electric power tool It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This is a spring designed to fit within the bit holder assembly of an impact driver, also known as an impact wrench. Positioned between the anvil and ring gear, this spring is accompanied by a washer and hog ring on each side to provide tension and maintain consistent pressure on the inserted bit within the holder. As a high-wear component, this spring will eventually wear out, resulting in a less secure grip on the bit by your driver and its hammer mechanism. This spring is equipped with a hook for secure attachment within the main housing. If the hook becomes damaged or misshapen, the entire spring will need replacement. To replace this spring, you will require a screwdriver and must partially disassemble the primary driver housing to access it.

This genuine OEM hog ring is used in impact drivers. It is a thick, circular wire with a diameter of 0.5 inches. It is positioned around the output shaft where it grips and secures the socket or adapter. Over time, the hog ring may corrode, break, or lose tension leading to socket instability. To remove a faulty hog ring, use needle-nose pliers or a small flat-head screwdriver to carefully pry it out of the mounting groove around the output shaft. Slide a new hog ring in the empty space until it locks into place. Inspect all the hog rings in your equipment and replace all those that are no longer functional. Each hog ring is sold individually.

Keep your impact driver or drill operating reliably with this retaining ring, a small but essential component that helps secure internal chuck and bit-retention parts in place. By preventing unwanted movement of key components, it helps maintain proper bit retention and consistent power transfer during operation. A worn, bent, or damaged retaining ring can lead to loose components, bit wobble, or retention issues, making replacement an important repair. Because retaining ring locations and sizes can vary between models, refer to your tool's parts diagram or service manual to confirm the correct application before installation. Sold individually.

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 8 Feet Long

Strong fastening depends on the anvil holding the driver bit securely while carrying each impact to the screw or bolt. Wear or damage may cause poor bit retention, excess movement, noise, or reduced power. Test with an undamaged bit and inspect the chuck parts before ordering a replacement. Match the assembly to the full tool model and service diagram. Disconnect the battery, wear eye protection around spring clips, use only the approved lubricant, and test the repaired tool at low speed first.

This is an authentic OEM part used in DeWALT and Porter Cable impact drivers. It fits between the anvil assembly and the sleeve. If it becomes lost or broken it will need replacing and a screwdriver may be needed during the installation. This part is made of urethane, a hard plastic, and is available individually.