Compressor Hardware

Compressor Clamp Hose .250 Id Genuine OEM replacement part, this item is sold individually. This part is used in various places in the compressors listed below. By its part name, it is used to clamp hoses onto certain parts on the compressors.

Compressor Compression Nut Genuine OEM replacement part designed for a variety of Air Compressors. This part is made out of Metal and it is Sold Individually. It does include sleeve. This item allows to connect two like-diameter fasteners or tubes.

Compressor Torx Screw Genuine OEM replacement part, this item is sold individually. This screw is used in various places in all of the tools listed below The most common use for this screw is to secure plastic housings together. It has a Torx T-20 head.

Compressor Assy Fastener This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individually. Purchasing spare screws is also encouraged, as they can wear out over time and regular use. A hex key and a screwdriver are helpful in the removal and replacement.

Compressor Ring Compression This is a genuine Craftsman part for use with Craftsman Air Compressors. The compression ring creates an airtight seal between the cylinder and piston and helps facilitate heat transfer between the piston and cylinder wall. The compression ring on a piston head is a wear and tear item. It is, often, a cause of an air compressor failing to produce air. This part is sold individually. Unplug the air compressor and bleed air from the tank before installing this part. Wear work gloves to protect your hands.

Compressor Graphite Gasket Kit Genuine OEM replacement parts kit. This Gasket Kit is used to prevent air leaks in the compressors listed below. Over time the gaskets will become compressed or cracked and you will hear an air leak coming from the compressor. They will need to be replaced. This would be a good time to inspect all the other wear parts of the compressor.

Compressor Pressure Switch Assembly Genuine OEM replacement part, this item is sold individually. A Pressure Switch controls the the compressor tank pressure. It will turn the compressor on when the tank pressure falls below the preset cut in point. It will also turn the compressor off at the preset cut point. This Pressure Switch is used on all of the compressor models shown below. One hose clamp included.

Compressor Hex Nut This is an OEM replacement part designed to fit Air Compressors. This nut is for the tube as it enters the head. It is made out of Metal and it is Sold Individually. To replace this item you would need a Wrench.

Compressor Nut, Set Of 2 These genuine OEM nuts come as a set of two and are essential components inside your portable air compressor. They play a crucial role in connecting the outlet tube to the pump assembly and the check valve. The pump is responsible for compressing air into the tank, while the check valve allows compressed air to enter the tank when open and maintains air pressure inside the tank when closed. You can determine if the nuts need replacement when they become loose or stripped, resulting in air leakage or an unstable connection. You may also notice excessive vibration or rattling from the compressor during operation, even when fully tightened. To replace the nuts, start by depressurizing the air tank by pulling the safety valve and draining any water from the tank by opening the drain valve. Remove the screws on the upper shroud to detach it from the compressor, following the instructions in your user manual to locate the nuts. You will typically need a socket or wrench to remove the pump assembly and lift it up from the machine. Fully loosen and remove the O-rings and nuts at both ends of the outlet tube. Please note that the nuts are sold separately from the O-rings.

Compressor Screw This screw is an authentic OEM replacement part sourced directly from the manufacturer. It is compatible with various models of electric compressors supplied by brands such as DeWALT, Black and Decker, and Bostitch. This screw should be replaced if it is lost or worn. It is made of metal and sold individually.